The Blue Table

[Thumbthumper]

This table isn't particularly special but is does have a bit of history.

SWMBO brought it with her to Canberra when she moved into a group house whilst studying at Uni.
Before that, it had been used for decades by old fellow called Jack in country Victoria to do his tax on.
It's been in our house for over ten years as a plant stand.

I feel it's time to give it a bit of love. It's Victorian Ash I believe. Probably early 1900's. I like the turnings and small dimensions. We'll find a use for it in the house.

1.jpg2.jpg

It'll just need a good clean and polish. I'll re-drill and replace all the dowels.
The top is very cupped, so I might use the saw kerf method (cut underneath) to flatten it.

More pics as I get some time to work on it.

[goodwoody]

Pine?

[Xanthorrhoeas]

The top is very cupped, so I might use the saw kerf method (cut underneath) to flatten it.

Hi,

don't forget to try the wet lawn in the sun trick before you go kerf cutting!

Good luck

David

[Thumbthumper]

Pine?

I originally thought it was Victorian Ash (Tassy Oak) because of the way the end grain looked.
I'm thinking now, after stripping it, that it may be Blackwood.

Hi,

don't forget to try the wet lawn in the sun trick before you go kerf cutting!

Good luck

David

I've already tried that . I left it on the wet lawn in the sun and clamped it to dry with some cauls afterwards.
Two days after removing the dry top from the clamps, it went back to where it was before

4.jpg

It's not too bad, but I do want to bring it down a bit more.

[Thumbthumper]

The parts are all stripped and washed.
The old dowel holes were drilled out, and the table glued up.

1.jpg2.jpg3.jpg

I'll work on the cupping in the top next.
A couple of fine saw kerfs underneath should do the trick.

[Horsecroft88]

Looking good, and apart from the top, a pretty straightforward resto on this one I would think Stu, for a guy with your skills.

Going on the pics, I too would plum for blackwood. The grain and colour seem right for that.

[hiroller]

Looking good.
What did you use to strip the paint?

[burraboy]

Looking good, and apart from the top, a pretty straightforward resto on this one I would think Stu, for a guy with your skills.

Going on the pics, I too would plum for blackwood. The grain and colour seem right for that.

Should that be 'plump'?

[Thumbthumper]

Looking good.
What did you use to strip the paint?

I prefer mechanical stripping if possible.
I used a shavehook and a card scraper.

After this I used paint stripper to soften the paint within the grain, and then gave it a good scrub with steel wool and metho.

[Thumbthumper]

I only needed to make a couple of saw cuts underneath the top.
The top will be nailed on, but I decided to put a couple of screws through the aprons into the top to pull it down as much as possible.

1.jpg2.jpg3.jpg

A couple of coats of shellac.

5.jpg6.jpg

The top's sitting nicely now.

4.jpg

[Thumbthumper]

The nail holes have been plugged with coloured wax.
It's had a light polish and a buffing with wax.

7.jpg

The table has been moved inside.
I've got it sitting next to my lounge chair. Perfect for my nightly glass of Shiraz

[Horsecroft88]

That is nice to see Stu, but mate, where is the glass of red ?? It seems to be missing in action. Well done, I am sure your wife must be most impressed with the table's rejuvenation. Cheers Dave

[Sawdust Maker]

Interesting what you can find under a few layers of paint

nice job but it looks like someone pinched your glass of Grange

[Christos]

Looks much better.

i often wonder if the home improvement would want to strip back to a more natural finish.

[Thumbthumper]

nice job but it looks like someone pinched your glass of Grange

If I could afford Grange, I would protect it with my life

Looks much better.
i often wonder if the home improvement would want to strip back to a more natural finish.

I hate shabby chic with a passion