Search:

Tag: inevitably

Search: Search took 0.00 seconds.

  1. Removing concrete splatter from ute tray

    Started by Reno RSS Feed, 26th August 2013 04:20 PM
    aluminium, builders, cleaned, concrete, cover, inevitably, load, mess, mix, mixer, product, read, remove, removing, renovateforum.com, shovel, splatter, straight, tarp, thread, tray, ute
    • Replies: 0
    • Views: 1,905
    Last Post: 26th August 2013 04:20 PM
    by Reno RSS Feed  Go to last post

    Forum:
    GENERAL ODDS N SODS

  2. How to fix some pin holes in lacquer

    Started by Arron, 11th November 2012 07:43 PM
    advise, air, arron, as-is, bubbles, cheers, craters, deep, fix, holes, inevitably, lacquer, leave, nitrocellulose, objects, pin, pin-hole, pulling, repair, sand, skills, sprayed, sprinking, start, stylwood, surface, tiny, wattyl, weeks, worse
    • Replies: 8
    • Views: 8,774
    Last Post: 18th November 2012 08:13 PM
    by Arron  Go to last post

    Forum:
    FINISHING

  3. Using "modern" lacquers - spray gun/folly?

    Started by Antipodes, 3rd August 2012 11:40 PM
    applied, booth, cans, coffee, control, corners, cutting, gratefully, gun or folly, ignorant, inevitably, job, kinda, lacquer, lacquers, layers, modern, nitro, passed, post-shellac, real, rubber, sanding, shellac, similar, spray, swedish, table, tips, world
    • Replies: 2
    • Views: 1,949
    Last Post: 12th August 2012 07:38 PM
    by Antipodes  Go to last post

    Forum:
    RESTORATION

  4. Using "modern" lacquers - spray gun/folly?

    Started by Antipodes, 5th August 2012 01:03 AM
    booth, booths, cans, coffee, control, corners, cutting, gun or folly, ignorant, inevitably, job, kinda, lacquer, lacquers, layers, modern, nitro, passable, passed, post-shellac, real, rent, restoration, sanding, similar, sounding, spray, swedish, table, world
    • Replies: 3
    • Views: 1,854
    Last Post: 6th August 2012 12:32 AM
    by Antipodes  Go to last post

    Forum:
    FINISHING

  5. Problem with Minwax

    Started by Arron, 11th August 2011 01:42 PM
    0000, apply, applying, beneficial, blemishes, canubra, dull, eee, fine, finish, gloss, glossy, grit, i’m, inevitably, looked, minwax, poly, problem, result, rub, sealer, steel, step, steps, surface, swirl, wax, wipe, wool
    • Replies: 11
    • Views: 3,972
    Last Post: 1st September 2011 05:32 PM
    by AUSSIE  Go to last post

    Forum:
    FINISHING

  6. NGR - to stain or not to stain...

    Started by woodmark, 31st August 2011 02:18 PM
    aim, applying, bit, brown, colour, considerably, couple, darken, darkening, doors, enhance, flakes, grain, hue, inevitably, light, ngr, occur, pattern, poly, possibly, sanding, sealer, shellac, stain, thoughts/ideas, timber, understand, visually, wondering
    • Replies: 1
    • Views: 1,995
    Last Post: 31st August 2011 02:45 PM
    by RufflyRustic  Go to last post

    Forum:
    FINISHING

  7. Acid-cleaning bricks around aluminium windows

    Started by ubeaut, 16th November 2008 07:18 AM
    acid, acid-cleaning, aluminium, bit, brand, brick, bricks, brickwork, cleaning, coated, damage, idea, inevitably, involved, paint, powder, reading, strip, surface, white, windows
    • Replies: 0
    • Views: 1,367
    Last Post: 16th November 2008 07:18 AM
    by ubeaut  Go to last post

    Forum:
    BRICKWORK, CONCRETING, PAVING, RENDERING, etc

  8. 15 amp outlets

    Started by gordonwindeyer, 15th April 2008 08:48 PM
    amp, converted, finding, gordon, inevitably, locations, outlets, power, single, singles, socket, sockets, spread, suboptimal, workshop
    • Replies: 8
    • Views: 2,526
    Last Post: 18th April 2008 11:11 AM
    by Stuart  Go to last post

    Forum:
    PLUMBING, ELECTRICAL, HEATING, COOLING, etc

  9. Hard Shellac for Bagpipes

    Started by McDuff, 14th January 2005 06:50 PM
    angles, applies, applying, bagpipes, bit, book, broom, close, clues, coats, concerned, convinced, correct, finish, flat, grain, handle, hard, idea, inevitably, lathe, neils, rag, read, run, set, shellac, shellawax, spindle, technique
    • Replies: 3
    • Views: 2,171
    Last Post: 15th January 2005 09:01 PM
    by Peter36  Go to last post

    Forum:
    FINISHING

Results 1 to 9 of 12