Results 1 to 4 of 4
  1. #1
    Join Date
    Feb 2007
    Location
    Sydney
    Posts
    87

    Post sizing hot water pipework for HWS

    I'm thinking of getting an instantaneous HWS and wondering whether or not I should also replace the main 1/2 inch hot water cu pipe from the existing water heater with say 3/4 inch lagged cu pipe. The system will be located at the rear and adjacent to the kitchen and I need to supply the bathroom nearer to the front of the house. What are the pros and cons to increasing the main feed to the bathroom to 3/4 inch lagged pipe? What are the regulations?

  2. #2
    Join Date
    Jul 2007
    Location
    Sydney-south
    Posts
    333

    Default

    Depends on how far the run is and how accessible it is. Most instantaneous heater manufacturers like to see you run 3/4 at least to the first branch so the thing works properly,this is assuming its a gas heater your thinking of installing. Also if your replacing a storage heater with instantaneous you must install a tempering valve, which governs the water temp to 50degrees to prevent scalding unless the heater you buy is factory preset at 50.

  3. #3
    Join Date
    Feb 2007
    Location
    Sydney
    Posts
    87

    Post

    thanks wp.

    The first branch is less than a metre from the hot water outlet with one feed going straight thru to the kitchen, another up the cavity to the bathroom (via the roof space) and another to an external (free standing) laundry in the opposite direction to the bathroom. The plan now is to have 3/4 for the main pipe to the first branch (split off to the laundry) and each branch using 1/2 inch lagged. Is the short 3/4 main pipe ok?

  4. #4
    Join Date
    Jan 2007
    Location
    Adelaide - West
    Age
    43
    Posts
    311

    Default

    Just a note: Instantaneous hws use the flow of water to lift the gas valve and let gas to the burrners- more water = more gas.

    That is why hws manufactures want 3/4 to the first branch, it encorages the unit to work more efficiently. The way you want it should be ok. Keeping in mind that the more pipe you have in a larger size the more cold "ded leg" water you'll draw off before you get hot water.

    As a general rule I put in 3 meters of 3/4 at the start of the run if possible. I have put less in under otherwise adverse conditions but not less than 1.5- this isnt law ,. its just i figure ive come to useing - because 3meters of pipe is 1/2 a length- therfore i get 2 hws out of one length.
    If you dont play it, it's not an instrument!

Similar Threads

  1. Electric hot water system making cold water
    By Nolesy in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 7
    Last Post: 14th December 2006, 08:36 PM
  2. Hot water goes cold in the pipes: what to do
    By silentC in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 31
    Last Post: 19th July 2006, 10:16 AM
  3. Hot water system - Temperature regulations
    By notrot in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 19
    Last Post: 13th September 2005, 05:54 AM
  4. Gas hot water heaters
    By Bob Willson in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 28
    Last Post: 29th March 2005, 12:16 PM
  5. changing tap washers on hot water taps
    By jackiew in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 85
    Last Post: 6th May 2004, 06:43 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •