![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 7 of 7
Thread: gable end and corner cuts
-
18th July 2007, 11:02 PM #1
gable end and corner cuts
I'm putting up the walls of my new colourbond shed. Its got the standard monclad wall sheets. Can anyone tell me how to cut the angle on the long sheets that cover the gable ends -should I fixing them to the frame, then cut them, or mark them, take them down, then cut them? What's should I use to cut them? Also where do I cut the sheets to make them fit for the corners (I'm using 75x75 corner flashing). Thanks for any advice.
-
20th July 2007, 10:23 PM #2
When I did the ends of my shed I fixed the sheets into position on one end and cut them by hand with snips while standing on the ladder 3.5m high.
The second end I fixed together on the floor , measured it all up , transferred the measurements onto the sheets and cut them on the ground with a grinder with a cutting disc and then fixed them to the end.
Both ways worked but the second way keeps the beer within reach.
johnm64
-
1st September 2007, 09:02 AM #3
Intermediate Member
- Join Date
- Aug 2007
- Location
- ACT
- Posts
- 9
Gable sheets
G'day - I'm about to do my gable ends today. Place the sheets up in the correct order, fix in place. Then run a chalk line from wall sheet end to the roof apex - using the top of the roof trusses or top hat (aka roof purlin - or roof batten) as your guide for the cut line line.
Once you chalk the cut line, use either a 4" grinder with a cutting wheel to cut the sheets - or a nibbler if you have one.
With the end corners for flashing, take your sheets flush with the end of the shed. You may get a little overlap with the wall sheet, but this doesn't matter as you will cover this with the 75x75 flashing. Any small flaws on the corner joins will be covered with the flashing.
Basically, put your sheets up, mark the angles - cut.
cheers and hope this helps
-
1st September 2007, 09:46 AM #4
I did pretty much the same thing. The sheets are big enough to handle by yourself anyway, let alone putting them up, then down, then up again.
I put a nick in each end of the sheets (one at gable, one at gutter) and used this to wedge the string line. Mark and cut, (I used angle grinder) and while I had the ladder there, I fixed off the rest of the screws (only had the overlaps to get the sheets up). Tin snips are better as they don't burn the sheet as it cuts, or for around $30.00, I have a diamond tipped wheel that I use for cutting the intricate bits in floor & wall tiles and this seemed to work a treat as it didn't heat up the sheet nearly as much.
And if you're worried about rust, get a small tin of bitumen based paint and paint any cut edges. I also used this around the bottom of the sheets where the concrete sits as concrete is corrosive.
Good luck.
Yonnee.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
1st September 2007, 02:55 PM #5
Senior Member
- Join Date
- May 2007
- Location
- Darwin NT
- Posts
- 81
If I cut with a grinder I go to a lot of trouble to clean the swarf off the roof or sheeting. It's easy to forget and later you get rust spots.
Also if I use a grinder, I allow say 5 mm extra and then cut neatly with snips. An edge cut with snips doesn't rust.
Cheers
Bill
-
2nd September 2007, 09:46 PM #6
Intermediate Member
- Join Date
- Aug 2007
- Location
- ACT
- Posts
- 9
-
10th September 2007, 05:00 PM #7
Bunnings do sell Orminoid, but any bitumen paint will do. I worked for autObarn and used the K&H aerosol for the tight spots. I painted from the bottom of the sheet to above where the concrete level.
I'd do a bit of an overlap to seal it properly.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.