![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 11 of 11
-
28th December 2006, 09:16 AM #1
Turning fluros off or leaving on.
I'm often wondering whether to turn the shed lights off or leave on.
Does anyone know if its cheaper to leave the fluro lights running for an hour than turn them off and then back on an hour later?
For that matter over what time frame is it more economical to leave the fluros on rather than turn them off.
I was told different responses from different sparkies.
Any thoughts
Thanks
Pulpo
-
28th December 2006, 09:25 AM #2
Senior Member
- Join Date
- Jun 2006
- Location
- the 'burn
- Posts
- 118
it would vary from circuit to circuit with things like wattage, number of tubes/fittings, type of starter
if it was just an hour you're talking about you're really only talking about a few cents saving either way, but there is probably more power saved than cash.
-
28th December 2006, 09:36 AM #3
Due to the amount of fluros I have, I leave them on all day once I have turned them on. I have 9 double fluros.
I actually did a test using some gear borrowed of a elec mate and the start up draw was equal to about 2 or 3 hrs running time.
It really depends on how many fluros you haveCheers
DJ
ADMIN
-
28th December 2006, 03:41 PM #4
I leave mine on all day......and all night when I forget......no economic reason, but its just easier.
There used to be a considerable saving in large factories, where they would calculate a strange figure called "power factor", and adjust the phase angle of the circuit until the power factor approached a certain amount (can't remember if it was 1 or 0) at which level the cost of running the flouros was zilch..
Head full of useless information!
Regards,
Noel
-
28th December 2006, 05:46 PM #5rrich Guest
This week, on The Discovery Channel show Mythbusters, this exact thing was tested and deMythified...
The measured energy to start fluros was equal to 23 seconds of operation. I believe that a rapid start or instant on fluro was the test device.
-
28th December 2006, 07:26 PM #6
Senior Member
- Join Date
- Jun 2006
- Location
- the 'burn
- Posts
- 118
you try get power factor as close to 1 as possible. off the top of my head, a lower power factor is "better" for the consumer as they are paying for less wattage but still drwaing the same current.
the difference between a power factor of .9 and .5 is that there is more wastage of current [heat losses, back emf's] in a .5 circuit. it doesn't do any actual work for you.
there are difficulties with supply with lower power factor, so places with low power factor have to spend heaps to rectify this, or they get hit with an extra tariff.
-
28th December 2006, 07:58 PM #7
Member
- Join Date
- Jun 2004
- Location
- Hamilton, New Zealand
- Age
- 87
- Posts
- 10
Turn Them Off
For the ordinary sheddie, there is only one answer to the question.
Turn them off.
A few thousand sheddies leaving their fluoros on when not required are:
contributing unnecessarily to global warming;
contributing unnecessarily to power company profits;
reducing the life of their tubes;
and,
wasting their own money.
I used to have a budget for over $2mill (NZ) at work for energy. The only answer is turn an item off, whatever it is, especially including computers.
If you have any doubt about the energy used by a fluoro, put your hand near to ballast (but don't touch for obvious safety reasons). There is a tremendous amount of heat generated by them.
The latest tubes (Tri-phosphorous) are very energy efficient, and give much better light than the equiv. incandescent, but regular cleaning is essential for maximum light especially in a dusty shed. The exterior static charge which is generated attracts dust which absorbs light.
Unless your installation is a few hundred fluroros don't get worried (and side-tracked) by power factor correction.
Wishing you all a bright New Year.
Cheers,
ROB NZ
-
16th January 2007, 11:21 AM #8
Leaving fluoros on to save money/energy is a total myth. And it doesn't make any difference as to how many fittings are involved.
Leaving them on costs you money.
-
16th January 2007, 11:53 AM #9
-
17th January 2007, 01:17 AM #10
-
23rd January 2007, 09:20 PM #11
China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 140