Results 1 to 6 of 6
  1. #1
    Join Date
    Dec 2008
    Location
    Bradbury
    Posts
    0

    Default Dining table - Hardwax oil

    Hi all.

    I’m refinishing my dining table using hardwax oil.
    I’ve done 3 coats, wiping off excess and leaving 24 hours between coats. I’ve lighting sanded with 600 between coats.

    It’s been 48 hours since the last coat and it’s still quite sticky. Is this normal?

    I was hoping to have the table back inside by tomorrow so I’m unsure what to do next. Any advice??


    Sent from my iPhone using Tapatalk

  2. #2
    Join Date
    May 1999
    Location
    Grovedale, Victoria Australia
    Age
    66
    Posts
    2

    Default

    All depends on how well the base finishes have dried before you put the next coat on, if still tacky it may be up to a week before it is dry to touch but will be 3-4 weeks before it is fully cured.
    Jim Carroll
    One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
    Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!

  3. #3
    Join Date
    Jan 2014
    Location
    Sydney Upper North Shore
    Posts
    710

    Default

    What brand of hard wax oil was it?

  4. #4
    Join Date
    Dec 2008
    Location
    Bradbury
    Posts
    0

    Default

    Quote Originally Posted by Jim Carroll View Post
    All depends on how well the base finishes have dried before you put the next coat on, if still tacky it may be up to a week before it is dry to touch but will be 3-4 weeks before it is fully cured.
    Should I lightly rub back with 1200 and add another light coat? Or wax even. The first and second coats were fine.
    Quote Originally Posted by Lappa View Post
    What brand of hard wax oil was it?
    Interbuild? Cheapie from Bunnings


    Sent from my iPhone using Tapatalk

  5. #5
    Join Date
    Jan 2014
    Location
    Sydney Upper North Shore
    Posts
    710

    Default

    Going by the SDS is mainly linseed oil. I’d be leaving it, as Jim said, to allow it to harden. Depending on how thick it went on it could take a couple of weeks. Hardwax oils are applied very thinly. I did my kitchen/sunroom table two weeks ago and I won’t use it for another week even though it’s dry. I did three coats allowing overnight to dry (at least 12 hours) between coats. My coats were touch dry in a couple of hours.

  6. #6
    Join Date
    Dec 2008
    Location
    Bradbury
    Posts
    0

    Default

    Quote Originally Posted by Lappa View Post
    Going by the SDS is mainly linseed oil. I’d be leaving it, as Jim said, to allow it to harden. Depending on how thick it went on it could take a couple of weeks. Hardwax oils are applied very thinly. I did my kitchen/sunroom table two weeks ago and I won’t use it for another week even though it’s dry. I did three coats allowing overnight to dry (at least 12 hours) between coats. My coats were touch dry in a couple of hours.
    Thanks for the info. Much appreciated. I guess I’ll wait it out and see how it goes.


    Sent from my iPhone using Tapatalk

Similar Threads

  1. Exterior hardwax oil?
    By brettule in forum FINISHING
    Replies: 0
    Last Post: 27th February 2019, 02:44 PM
  2. Whittle waxes hardwax oil
    By qwertyu in forum FINISHING
    Replies: 1
    Last Post: 13th November 2018, 12:56 PM
  3. OSMO Hardwax or similar?
    By The Good Egg in forum FINISHING
    Replies: 7
    Last Post: 13th November 2011, 11:27 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •