![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 5 of 5
-
10th July 2014, 04:20 PM #1
New Member
- Join Date
- Jul 2012
- Location
- Australia
- Posts
- 2
Finish for a Bamboo kitchen benchtop
Hi guys,
We've made the decision, rightly or wrongly, to go with the Bunnings Kaboodle bamboo benchtops for our new kitchen. I thought it was all good, but now I've done some more research I've thoroughly confused myself re: the best finish for these benches.
From what I can tell, my options are something like the below. But I'd love some experienced opinions / comments as I'm not sure all of my information is accurate.
Tung Oil
+ good waterproofing provided time is spent to ensure decent penetration
+ small defects can be patched easily
- takes a long time to apply / cure properly
- if it doesn't dry you might end up with a permanently "oily" surface
- stains may still penetrate and leave permanent marks (eg: glass / coffee cup rings)
- regular refinishing required
Tung Oil + Beeswax
+ / - same as above, possibly with better waterproofing without the same penetration level
- seems to be difficult to find (possibly needs to be made using the 2 ingredients separately)
Floor Polyurethane
+ easier / quicker finish to achieve waterproofing
+ better protection against stains etc
- small scratches / marks can allow water underneath
- fixing these small imperfections means sanding and refinishing the entire benchtop
Livos Kunos Counter top oil
+ / - I'm not quite sure what the pros and cons are here.
Other?
Any help would be greatly appreciated. Cheers.
-
11th July 2014, 12:22 PM #2
The Livos lady
- Join Date
- Feb 2011
- Location
- Melbourne
- Posts
- 206
bench top finsh
The belowis from experience with these products and articles I have researched andwritten and are my viewpoint and not made in stone. Any product, if not appliedas it should, will create problems. Also, keep an eye on temperature, sandinggrits for the finish that you will use and curing times of products. Speak directly withmanufactures or someone who has actually used the specific product.
Tung oil...dependson the product. If natural tung oil, it has no body so you will need many coatsto create some sort of seal. If modified, you create a type of coating thatwhen scratched or worn, may be difficult to fix..and it is not food safe.
Beeswax..againdepending on the product will need maintenance as it wears and as it sits ontop of the surface, it can leave duller sections in areas where is used often.
Poly, yeseasier, smeller and all the issues you state.
LivosKunos Countertop oil...Ok, I am a bit biased here so have a listen to what NeilScobie has to say about it and then give Livos a call. Why furniture craftsman and woodturner Neil Scobie chooses Livos natural oils - YouTube=
Always good to do a test application too as often bamboo is pretreated and being so dense will not absorb much product.
Good luck with it.Livos Australia
<O</O
-
11th July 2014, 12:28 PM #3
New Member
- Join Date
- Jul 2012
- Location
- Australia
- Posts
- 2
-
11th July 2014, 12:48 PM #4
Disclaimer: I do not work or advertise for Organoil, I have simply found that Hard Burnishing Oil gives a better finish than most other Oils. I have not tried Livos.
Hi JDellit,
I
have used Tung oil from several different sources and from personal experience working with everything from Wenge through Huon Pine and down to Australian Oak.
The product that I use most is Organoil Hard Burnishing Oil, which is Tung Oil with some dryers and other bits and pieces in it. But it is mainly Tung Oil.
I'd like to say right up that Tung Oil is described as Food Safe by the FDA in America, I'd also like to say that you don't need lots of coats to get a finish resistant to heat and moisture.
Bamboo can be difficult because of it's polished natural appearance, which may affect hard burnishing, but unless you try this method out on some scrap, you won't know.
If you look at this thread you will see pictures of several oils being evaluated for their finish and durability.
Regardless of what you use, you will need to be careful to properly finish around the sink area.
I'm happy to talk further with regard to the method if you want. Just PM me.
Incidentally, where in Australia do you live?
Regards,
Rob
-
11th July 2014, 10:40 PM #5
What sort of look do you want?
If you want a really high gloss and a "None shall pass!" style of waterproof coating, then one of the tabletop epoxies would be your best bet.
That said, there's a lot to be praised about the refinishability of oil.
Similar Threads
-
Finish for kitchen benchtop
By delbs in forum FINISHINGReplies: 8Last Post: 22nd May 2013, 10:35 PM -
Kitchen benchtop finish
By reprint in forum FINISHINGReplies: 7Last Post: 17th May 2012, 11:25 AM -
How to finish a kitchen benchtop (Marri) To oil or not to oil ??
By maverickhouse in forum FINISHINGReplies: 3Last Post: 4th November 2011, 08:35 PM -
finish for kitchen benchtop
By Ren in forum FINISHINGReplies: 2Last Post: 22nd January 2003, 07:19 PM -
Kitchen and benchtop finish??
By Rod Smith in forum FINISHINGReplies: 0Last Post: 5th July 1999, 09:37 PM