![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 15 of 17
Thread: tung oil finish!
-
2nd May 2012, 12:58 PM #1
Novice
- Join Date
- Apr 2012
- Location
- Mount Gambier
- Posts
- 6
tung oil finish!
I have read the Sam Maloof recipe, tung oil, boiled linseed and varnish, however my question is...it says to use raw tung oil and I have read that raw tung oil takes a loooong time to dry. What I am guessing is that the varnish and the driers in the boiled linseed oil will help the raw tung oil to dry am I right in thinking this way???
I am also guessing that this finish would be better wearing than just a raw tung oil finish.
Also wondering if anyone knows how the Sa,m Maloof finish goes for water resistence etc. eg coffee cup marks. Some advice would be much appreciated Thanks
-
2nd May 2012, 03:44 PM #2
The Russel Coyte of Woodworking
- Join Date
- Mar 2009
- Location
- Brisbane, Australia
- Age
- 52
- Posts
- 9
mate
I am keen to hear from others too as I am starting to think about finishes for my bench.
I have always used Danish oil on most of my picture frames, boxes and Toolbox I have built. I read the can and they say that Danish oil is a blend of Tung Oil.
Interestingly the manufacturer states that their Danish oil is not suitable for table/bench tops? They recomend one of their other products but for my mind Danish oil will be absolutley fine for a workbench.
It was mentioned to me that the Boiled Linseed/Turps/Varnish option is a great one but depending on your weather it does take some time to dry.
Keen to hear other opinions.
Cheers
Milo
-
2nd May 2012, 04:12 PM #3
For both your purposes, I would recommend Organoil Hard Burnishing Oil. This is Tung Oil mixed with "11 secret herbs and spices". Resistant to heat and moisture,wipes clean with "Spray and Wipe" or other kitchen cleaner. Applies easily (so long as you have a Random Orbital Sander) and food safe.
Gives a great finish and dries quickly too!
Regards,
Rob
-
2nd May 2012, 09:57 PM #4
Novice
- Join Date
- Apr 2012
- Location
- Mount Gambier
- Posts
- 6
maloof mix
Thanks Milo and Rob for your replies,
I have heard the Organoil is good but did not realise it was tung oil based, I have just ordered some pure tung oil so I guess I will give the Maloof mix a go. I will be using Cabots floor poly gloss, pure tung oil and boiled linseed oil probabally with some turps for better penetration. Still not too sure how long this will take to dry I am hoping not too long, have heard you can add dryers for quicker drying finish but as I wrote in my last post, I am hoping the dryers in the linseed oil and maybe the poly will help it dry quicker.
-
2nd May 2012, 10:22 PM #5
SENIOR MEMBER
- Join Date
- Aug 2008
- Location
- Normanhurst NSW 2076
- Age
- 82
- Posts
- 0
Hello Bustler74,
There is a publication called "POLISHER'S HANDBOOK". Highly recommended. So far as the Maloof mix is concerned, my word of caution is to try it out on a scrap piece first, preferably the same wood. I would definitely recommend against adding dryers. Drillit.Last edited by Drillit; 2nd May 2012 at 10:25 PM. Reason: typo
-
3rd May 2012, 01:01 PM #6
Novice
- Join Date
- Apr 2012
- Location
- Mount Gambier
- Posts
- 6
maloof mix
Hey Drillit,
sounds like a good idea to try it out on a scrap piece firstwill check out the book you recommend cheers
-
4th May 2012, 09:31 PM #7
Don't forget that Sam said wipe it on liberally and leave it for about 10-15 min then thoughly wipe of the excess. He did up to 5 or six coats and there is a second mix that goes on after it to finish with 3 coats.
SBPower corrupts, absolute power means we can run a hell of alot of power tools
-
7th May 2012, 10:29 AM #8
Novice
- Join Date
- Apr 2012
- Location
- Mount Gambier
- Posts
- 6
maloof mix
Hello Superbunny,
Thanks for your reply, but after much research have decided to try the Organoil Hard burnishing oil, have had some good reports.
-
9th May 2012, 10:52 AM #9
Boucher de Bois
- Join Date
- May 2010
- Location
- Wellington, NZ
- Posts
- 0
I use a local product that I suspect is pretty similar to the Hard Burnishing Oil - it's basically a blend of tung oil, vege turps and driers. I used it on an oak dining table that gets used without a table cloth and has to put up with the worst that a pair of toddlers can throw at it. It seems to work very well indeed, and has been resistant to moisture and hot mugs etc so far.
-
9th May 2012, 11:06 AM #10
Member
- Join Date
- Jan 2012
- Location
- Baton Rouge
- Posts
- 19
So how would you guys say this Maloof mix and Hard Burnishing Oil compare to Waterlox, which is a tung blend I believe?
Sorry if this is a thread jack. Just seemed pertinent to the topic.
-
10th May 2012, 11:24 PM #11
Novice
- Join Date
- Apr 2012
- Location
- Mount Gambier
- Posts
- 6
organoil, burnishing oil
Hey NZ stu,
Thanks for your reply, sounds like the tung oil burnishing oil mixes are pretty good. Did you use the random orbital sanding burnishing method od did you do it by hand?
In reply to Fricasseekid's question, I am not familiar with waterlox...so I cant comment sorry.
-
11th May 2012, 09:33 AM #12
Boucher de Bois
- Join Date
- May 2010
- Location
- Wellington, NZ
- Posts
- 0
I basically dry sanded to 320 grit, applied a couple of coats of oil, then wet sanded (by hand, using the oil as a lubricant) through 400-600-800-1200 grit.
I not sure whether the same technique would work with the organoil though: they tend to say that you should follow thier method to the letter.
-
11th May 2012, 10:47 AM #13
Member
- Join Date
- Jan 2012
- Location
- Baton Rouge
- Posts
- 19
How many Stuarts are on this forum?!
-
11th May 2012, 11:37 AM #14
Boucher de Bois
- Join Date
- May 2010
- Location
- Wellington, NZ
- Posts
- 0
-
11th May 2012, 01:43 PM #15
Senior Member
- Join Date
- Mar 2009
- Location
- Hobart
- Posts
- 410
I have used a Tung oil based product (Feast Watson Floor Seal) and a couple of other manufacturers products for many years now. As to the proportion of raw Tung oil, to poly, or over ingredients I have no idea. I have used these products in my kitchen, benchtops, doors which are likely to get splashed with water (ie. close to sink/stove), splashbacks, vanity unit in bathroom and also on the floors throughout my two houses. I am not really a fan of linseed oil, as from my experience it is slow drying, messy, and doesn't wear very well at all.
The one thing I find with the Tung oil product is that it is pretty durable, and importantly doesn't seem to be affected by heat or water as a rule. The other good thing about it, is that if marked, it is so easy to repair. A light scratching back with sandpaper and a re-coat and it is good as gold.
I do need to qualify these remarks by saying that my kitchen benchtop at home now does show some considerable wear, and a little water damage, but that is some 10 years since it was originally applied and then and only immediately around the sink edge. Overall I am impressed and once I have sanded the benchtop back will re-coat with 2-3 coats of the same product and I am confident all will be fine.
I did try the organo-oil around the benchtops either side of my stove, and it too has held up superbly. All I ever seem to need to do is give it the occasional bees wax polish and it too remains looking good. I would be keen to try this product again also. I do though tend not to allow water to sit on the surface for long and I am also careful about putting hot pots/pans etc directly onto the surface.
Similar Threads
-
Pure Tung Oil Finish
By kandiman in forum FINISHINGReplies: 7Last Post: 25th July 2009, 05:37 PM -
Tung Oil Finish Thickening In Can
By Paul39 in forum FINISHINGReplies: 4Last Post: 6th July 2009, 04:51 PM -
MDF FINISH - Tung/Poly/Wax
By dazzler in forum FINISHINGReplies: 3Last Post: 13th February 2006, 04:56 PM -
Tung oil finish help needed
By Firewalker in forum FINISHINGReplies: 7Last Post: 10th November 2005, 11:19 PM -
Finish to dining table - tung oil?
By Mario G in forum FINISHINGReplies: 4Last Post: 21st May 2003, 11:58 PM