![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 7 of 7
Thread: Slab size for new shed
-
6th September 2007, 09:15 AM #1
Novice
- Join Date
- Sep 2007
- Location
- NSW
- Posts
- 8
Slab size for new shed
G'day all
First time poster, so apologies if this question has been asked too many times. I'm looking to lay a slab for a 7.5 x 3.75m shed, and I'm unsure how much bigger the slab should be. Would 100mm be enough, or do I need to go 200 or even 300 ?
Cheers Phil
-
6th September 2007, 09:37 AM #2
Intermediate Member
- Join Date
- Aug 2007
- Location
- ACT
- Posts
- 9
Hey there Phil - I just went through the same thing, although I had my slab laid by a professional concreter.
From my limited experience, I'd say the dimensions of the slab really depend on how you are going to construct the shed. For example, if you intend to set the side and rear walls on top of the slab, then the slab will need to be wider than the oustide dimensions of the shed. If not, the slab needs to be the same dimension as the shed, as the sheets will fit neatly over the concrete.
I prefer the latter method as then there is not such an issue with water getting in under the sheets as there would be if the sheets sit on top of the concrete.
To answer your question more specifically though, if you are setting sheets on top of the concrete, I wouldn't imagine there would be any main structual difference between 50mm to 100mm to 300mm - although the bigger the difference, the more water may pool on the edges and rust sheets quicker.
Don't forget, you may have a set back of side posts from the edge of the concrete to allow for side and rear battens which wall sheets are screwed to. So the outside edge of the posts will be in from the edge of the concrete by say 60mm to allow for the protrusion of the wall batten.
Hope this helps. Importanly, I hope the rationale is sound!
cheers
DNL
-
6th September 2007, 09:57 AM #3
Hi Phil
I think DNL has covered most of it except to that if you're buying the shed in (not building it from scratch) then discuss it with your supplier. The main point I would recommend is don't have the top surface of the concrete at ground level - err on being higher rather than lower. I have seen a number set at ground level which when you get heavy rain the surface flooding flows into the shed. Check your property for slope and run-off from the neighbours as well. It's easier to put in a ramp/step to get into the shed than to have to bail it out
I think the time on my tuppence has just run out.
Ken
-
6th September 2007, 10:01 AM #4
There is of course another way, pour the slab inside the shed after it is erected. This is the method I used my current shed and the last one.
Makes it a little harder to erect the shed, but it pays of in having a good seal between slab and shed, no nasties and water can get in.
This current shed used brackets and plates that were concreted into 600mm deep holes, then the frames were bolted on top, 100x50RHS, nice method of construction.
Last shed was C-channel with frames concreted in holes, bit harder to do.
-
6th September 2007, 10:08 AM #5
Novice
- Join Date
- Sep 2007
- Location
- NSW
- Posts
- 8
-
6th September 2007, 07:19 PM #6
If you are pouring the slab before hand you will need to be relatively exact in the squareness of it, which is no big deal really.
I also suggest boxing a 25mm recess around the edge of the slab to stop water seeping under the walling IF your iron doesnt continue down past the level of the slab.Jack
-
10th September 2007, 02:44 PM #7
My last two sheds I've built myself have had the slabs poured after the shed was erected. As has been said, this provides a seal around the bottom of the shed without much extra work.
However...
...concrete is corrosive and over a long period of time can rust away the bottom of the sheets. In my current shed, I simply painted the bottoms of the inside of the sheets in Bitumen paint, providing a protective layer for the sheets.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
Similar Threads
-
Slab for shed before or after?
By Com_VC in forum THE GARDEN SHEDReplies: 7Last Post: 14th July 2007, 10:31 PM -
Concrete slab for shed
By atregent in forum THE GARDEN SHEDReplies: 9Last Post: 12th February 2007, 01:45 PM -
New shed (p2) and new difficulties and ??
By LeoAU in forum THE GARDEN SHEDReplies: 5Last Post: 22nd January 2007, 02:26 PM -
Snakes in the shed!
By Wild Dingo in forum THE GARDEN SHEDReplies: 70Last Post: 21st January 2007, 08:07 AM