Search:

Tag: cfm

Search: Search took 0.00 seconds.

  1. Spray finishing Newbie - Looking for recommendations on Startup

    Started by kenny12, 20th June 2013 07:11 AM
    $550+, 100, 4-6, 6-8cfm, 7cfm, air, applicaions, buy, cfm, compressor, current, delivery, earlex, finishing, free, gun, hoping, hvlp, low, newbie, pressure, recommendations, setup, speed, spray, spraygun, spraying, startup, station, water
    • Replies: 8
    • Views: 2,029
    Last Post: 26th June 2013 07:07 PM
    by Arron  Go to last post

    Forum:
    FINISHING

  2. Suggest a compressor

    Started by icor1031, 23rd May 2012 08:53 PM
    2.2, adequate, automotive, belong, cfm, compressor, compressors, edit, fine, finish, gallon, gun, guns, hvlp, idea, lowes, painting, projects, properly, psi, run, running, scfm, suggest, woodwork
    • Replies: 3
    • Views: 1,811
    Last Post: 28th May 2012 11:13 AM
    by Bob38S  Go to last post

    Forum:
    FINISHING

  3. Spray gun for Feast Watson floor seal

    Started by jarrah jack, 13th May 2011 11:09 AM
    advance, btw, cfm, compressor, ebay, feast, feed, floor, floorseal, gravity, gun, iwata, keen, nosel, paying, recommend, reply, seal, size, spray, spraying, time, unit, watson
    • Replies: 1
    • Views: 1,852
    Last Post: 13th May 2011 06:09 PM
    by hobbyst  Go to last post

    Forum:
    FINISHING

  4. Sprayguns

    Started by Chris Parks, 20th February 2010 10:10 PM
    air, bouncing, brand, buy, cfm, choice, continuously, conversion, days, finishes, gun, guns, hose, hvlp, life, loss, lot, minimum, paint, painted, required, search, simple, size, sprayguns, spraying, supply, system, type, volume
    • Replies: 0
    • Views: 959
    Last Post: 20th February 2010 10:10 PM
    by Chris Parks  Go to last post

    Forum:
    FINISHING

  5. Arnold De Vilbiss "Tuffy" Compressor

    Started by Jim Miley, 29th July 2007 06:29 PM
    air, arnold, cfm, compact, compressor, compressors, crankcase, diaphragm, diving, equivalent, filters, forums, gday, hooka, jim, lightweight, modern, oil, output, rate, reason, replacement, require, shallow, simple, suitable, time, tuffy, unit, vilbiss
    • Replies: 3
    • Views: 5,355
    Last Post: 31st July 2007 07:24 PM
    by echnidna  Go to last post

    Forum:
    NOTHING AT ALL TO DO WITH RENOVATION

  6. Any spray guru's out there?

    Started by BrettC, 27th November 2006 10:59 AM
    15.2, 3hp, @115, advised, appreciated, assistance, based, belt, bit, cfm, compressor, confused, displaces, drive, gun, guru, gurus, hvlp, lacquer, ltr, lvlp, opinions, psi, pump, question, recommendations, shellac, spray, spraying, tank
    • Replies: 12
    • Views: 3,958
    Last Post: 28th November 2006 10:32 AM
    by BrettC  Go to last post

    Forum:
    FINISHING

  7. Dusty air flow - some measurements

    Started by BobL, 22nd May 2006 11:03 PM
    0.5m, 100mm, 2.5m, 360o, 45o, 90o, air, bag, cfm, clean, conclusion, dirty, dusty, efficiency, elbow, experiment, flexible, flow, hose, iii, impeller, intake, measurements, pipe, pvc, run, runs, sawdust, speed, total
    • Replies: 14
    • Views: 2,882
    Last Post: 25th May 2006 02:02 AM
    by Skew ChiDAMN!!  Go to last post

    Forum:
    SAFETY

  8. Used air cleaner giveaway

    Started by BobL, 5th April 2006 10:01 AM
    0.3, 1200, 640, absolute, air, cfm, cleaner, coated, corroded, cost, difficult, filter, filters, finer, free, giveaway, guess, half, hepa, laboratories, micron, partly, prefilter, rated, shed, size, sizes, stands, suit, units
    • Replies: 3
    • Views: 2,171
    Last Post: 6th April 2006 10:23 PM
    by scooter  Go to last post

    Forum:
    SAFETY

  9. WOODWORKING QUIZ for 18 Oct 04

    Started by Ralph Jones, 18th October 2004 09:47 PM
    achieve, air, amount, buy, cfm, collector, correct, dust, evening, friends, hour, job, motor/fan, oct, plan, quiz, ready, recycle, respectfully, shop, size, times, woodworking
    • Replies: 8
    • Views: 1,962
    Last Post: 20th October 2004 09:16 AM
    by Wood Borer  Go to last post

    Forum:
    Woodies Quiz Forum

  10. ? - CIG DeVilbiss gun - what CFM required

    Started by eddie the eagle, 25th April 2004 12:11 AM
    250cfm, 2mm, air, beasties, cfm, cheap, cheers, cig, compressor, devilbiss, eddie, gun, guns, light, orifice, piped, rating, required, requirement, running, shed, similar, size, spent, sprayed, successfully, supply, system, time, websites
    • Replies: 3
    • Views: 5,492
    Last Post: 15th May 2004 06:06 PM
    by eddie the eagle  Go to last post

    Forum:
    FINISHING

Results 1 to 10 of 10