Search:

Tag: rpm

Search: Search took 0.00 seconds.

  1. Colt Maxicut Forstner bits - deep boring test

    Started by rsser, 15th December 2011 01:59 PM
    2 Pages •
    1 2
    angle, bevel, bit, bits, boring, brett, chipping, chips, cold, colt, deep, easy, edge, extension, flute, forstner, hcs, heat, hss, lathe, leonard, maxicut, paddle, rotastop, rpm, sharpening, speed, steel, test, wear
    • Replies: 23
    • Views: 7,335
    Last Post: 17th December 2011 03:30 PM
    by NeilS  Go to last post

    Forum:
    PRODUCT REVIEWS

  2. Safety Glasses

    Started by smidsy, 5th August 2011 06:31 PM
    2 Pages •
    1 2
    11000, arts, cheers, coming, commonly, faster, fragments, glasses, grinder, grinders, guessing, hazards, impact, load, machining, material, medium, metres, paul, powered, practical, rpm, safety, school, shield, sparks, speed, standard, teach, tool
    • Replies: 17
    • Views: 4,545
    Last Post: 19th September 2011 10:41 AM
    by HazzaB  Go to last post

    Forum:
    SAFETY

  3. Swansdown Mop Speed

    Started by skot, 11th August 2011 11:45 PM
    150mm, 200mm, 2980, answer, bench, brisbane, buff, fast, grinder, locate, mop, neil, purchased, rpm, search, speed, spindle, swansdown, tapered, wwws
    • Replies: 1
    • Views: 1,140
    Last Post: 12th August 2011 12:14 AM
    by China  Go to last post

    Forum:
    FINISHING

  4. Buffing Organoil

    Started by Scott Taylor, 14th March 2011 09:46 AM
    600-2000, buff, buffer, buffing, burnishing, finishing, gday, gingin, hard, lambs, oil, organoil, organoils, power, question, range, rpm, speed, stage, suggest, theory, wool
    • Replies: 3
    • Views: 1,994
    Last Post: 30th March 2011 06:49 PM
    by Paulphot  Go to last post

    Forum:
    FINISHING

  5. Removing Clutch on a Stihl Trimmer?..

    Started by Batpig, 28th November 2008 06:50 PM
    batpig, broken, clutch, cool, cooling, dear, diameter, fairly, fins, freely, front, inside, jam, low, motor, motors, outer-housing, pipe, removing, rpm, setup, shiny, spins, spring, stihl, stumped, trimmer, twist, typical, wrench
    • Replies: 3
    • Views: 12,068
    Last Post: 7th June 2009 09:04 AM
    by uwheelsgy  Go to last post

    Forum:
    NOTHING AT ALL TO DO WITH RENOVATION

  6. 2-stroke M'cycle Oil in a Mower or Edger?...

    Started by Batpig, 26th November 2008 06:40 PM
    2-stroke, 2stroke, batpig, bike, blokes, dear, edger, extra, involved, mcycle, motorcycle, mower, oil, petrol, probs, putting, quality, rpm, soluble, special, specials, stuff, supercheap, surely, time, variations, waddya
    • Replies: 5
    • Views: 6,200
    Last Post: 28th November 2008 07:43 AM
    by Batpig  Go to last post

    Forum:
    NOTHING AT ALL TO DO WITH RENOVATION

  7. Want to drill a 3rd hole in a 2-hole Vanity Basin...

    Started by Batpig, 27th October 2007 05:13 PM
    2-hole, 2hole, 3-hole, 3rd, 6mm-thick, approximately, basin, basins, brand, cutter, drill, drilling, fairly, hole, hole-saw, light, lubricate, machine, n.b, oil, pillar, pressure, rpm, spout, style, taps, teeth, tungsten-grit, vanity, vitreous-china
    • Replies: 10
    • Views: 8,114
    Last Post: 1st November 2007 11:14 PM
    by manoftalent  Go to last post

    Forum:
    BATHROOM & TOILET

  8. Diesel powered cars

    Started by Guy, 23rd August 2006 09:52 AM
    bonded, brakes, capacity, car, carbon, cars, clutches, composite, compound, connected, dampers, diesel, drive, engine, final, forward, front, litres, multi-plate, oil-immersed, pinion, powered, rack, rear, rpm, spaceframe, tank, transmission, tube, twin
    • Replies: 3
    • Views: 1,653
    Last Post: 24th August 2006 02:43 PM
    by Wildman  Go to last post

    Forum:
    NOTHING AT ALL TO DO WITH RENOVATION

  9. Removing circular marks after polishing

    Started by Don Nethercott, 15th August 2004 04:18 PM
    100, 1140, 120, 150, 180, 600, bowls, canberra, can’t, carba-tec, catalogue, circular, correct, don, hard, ideas, it’s, lathe, marks, polish, polishing, press, removing, rpm, run, sand, shellawax, southern, woodturning, wrong
    • Replies: 9
    • Views: 2,786
    Last Post: 17th August 2004 07:27 PM
    by ubeaut  Go to last post

    Forum:
    FINISHING

Results 1 to 9 of 32