Results 1 to 7 of 7
  1. #1
    Join Date
    May 2020
    Location
    Melville, WA
    Age
    60
    Posts
    20

    Default Door triming and installation

    Hi, I am hoping to reach out to anyone that knows about doors.

    Just purchased a Hume external door 2040 x 820 from our mate Bunnings.

    The old frame and old door is 807 wide (and when you look at the old door from the inside I am convinced its a jarrah frame)

    The sticker says do not trim more than 3mm from the edge. I need to do a bit more than that. Looking at the exposed bottom and the long edge it appears to be 25mm thick - see photo.

    Can I trim 13m from the width of the door (say 7mm from each side and still have enough of the long edge frame to hold firmly.

    Once trimmed, it will get a seriously thick coating of paint. My internal doors at home swell in winter and stick then in summer they shrink so much that they don't lock. Builder says nothing wrong with his work - go figure.


    The door frame is well and truely in place and is not worth taking off.



    (this is the least of my issues - I don't have one of those coring bits that will do a 54mm hole. I might have to take it to a friendly mens shed to do the deed. Not worth buying one for one hole)


    Thanks
    20231208_143109.jpg

  2. #2
    Join Date
    Nov 2017
    Location
    Melbourne
    Age
    73
    Posts
    108

    Default

    Is your measurement of 25mm the full thickness of the door or just the stile, being the vertical solid timber sandwiched between the hardboard sides? I haven't seen 25mm as a full thickness in off the shelf external doors. Standard internal and external door full thickness is 35mm, being 27mm stiles and rails plus two faces at 4mm each, although there are thicker off the shelf external doors.

    Assuming your door is a hollow core and standard thickness of 35mm with 27mm stiles, it's not ideal but, yes, you can take 6.5 - 7 mm off each side if you accept that this will void the manufacturer's warranty if the manufacturer states maximum 3mm off. It's your problem if the door fails in future. Some manufacturers in the past and maybe now stated maximum trim of 5mm each side, so an extra 1.5 - 2mm each side isn't massive.

    You might encounter problems with the lock block, which is a piece of solid timber usually in the middle of the door on the lock side. Depending on how generous the manufacturer has been with the depth of the block from the edge, when you drill your hole for the handle you might go outside the block. From a practical point of view this doesn't matter much as long as you don't deform the unsupported faces by over tightening a horizontal lock screw outside the lock block . If the screws are vertical this shouldn't be an issue as they should be supported by the lock block.

    Hollow core doors are held together as much by the honeycomb interior glued to the faces as by the stiles and rails. I've worked on old doors that have been trimmed much more than you're doing and a few with missing bottom rails and they've held together alright for years.

    The surest way to cause a painted exterior door to die prematurely is to ignore the manufacturer's instructions to seal the top and bottom rails, which many people fail to do. You can get away with it on internal doors and it's commonly done, but not on external doors.

    All that said, you'd be a lot better off returning the door to Bunnings and ordering a custom made right size door which doesn't require trimming. It'll cost more but in the short and long runs it's worth it for avoiding trimming the door and keeping your warranty.

    Bunnings might still offer a reasonably priced installation service if you buy the door from them. I say it is / was reasonably priced because Bunnings' contractor (Grey Army) approached me a couple of years ago to install Bunnings' doors. I think Bunnings charged customers $120 and I would have got $60. It didn't proceed, not least because I got a lot more than $120 for door swaps, never mind a lousy $60.

  3. #3
    Join Date
    Aug 2004
    Location
    Perth WA
    Posts
    355

    Default

    Take it back, get a refund and then order one to your specific size.
    Experienced in removing the tree from the furniture

  4. #4
    Join Date
    May 2020
    Location
    Melville, WA
    Age
    60
    Posts
    20

    Default

    Thanks for the reply.

    The door thickness is 35mm. Its the stile that I am talking about.

    Bunnings fitting is $300 - I asked. More than twice the price of the door + door knob + hinges (oh and delivery!. (I asked)
    It is an external door (so even though they say solid I think its "pretend solid"

    I am happy with voiding the warranty in this instance as it will only serve as an entry point for the man cave. Its not a fort knox building.

    The most important thing for me here is to make sure that its sealed and painted well and good as it will be open to the elements.




    Thanks
    N

  5. #5
    Join Date
    Nov 2017
    Location
    Melbourne
    Age
    73
    Posts
    108

    Default

    Quote Originally Posted by NicA View Post
    It is an external door (so even though they say solid I think its "pretend solid"
    The grades of door, starting from the bottom in structure and price, are hollow core, solid core and solid.

    Solid is solid timber all the way through, but usually made up from different strips and or panels of timber as a single slab would be very expensive.

    Solid core and hollow core look the same from the outside as both have hardboard faces glued to visible rails and stiles, but hollow core has honeycomb core and is mostly voids where solid core has solid timber core made up of small pieces of timber glued together. So yours would be solid core. You can tell by the significant difference in weight between a hollow and solid core door.

    Solid core is supposed to be more stable than hollow core.

  6. #6
    Join Date
    Apr 2011
    Location
    se Melbourne
    Age
    63
    Posts
    189

    Default

    If I was asked to install this door, I would be confident in trimming 7mm off each side. Might be different with a hollow door as there is less for the hinge screws to grip.
    If a solid door might require a second person, even semi solid is heavy enough.

    My price to install would be about $200 - about 3 hours labor. Painting is extra.
    Best to pre trim and paint all sides before installing.

  7. #7
    Join Date
    Nov 2017
    Location
    Melbourne
    Age
    73
    Posts
    108

    Default

    Quote Originally Posted by Handyjack View Post
    If I was asked to install this door, I would be confident in trimming 7mm off each side. Might be different with a hollow door as there is less for the hinge screws to grip.
    Agree. My original post assumed it was a hollow core.

    Quote Originally Posted by Handyjack View Post
    My price to install would be about $200 - about 3 hours labor.
    I'd charge about $220 - $300 depending on how square the jamb is and whether I have to trim the new door out of square and or fix the jamb and whether it's a simple handle or a handle and separate deadlock. I'm about the same time for labour. I always reckon I should be able to do it in 2 hours but it almost always runs out to about 3 hours, sometimes more.

    Quote Originally Posted by Handyjack View Post
    Painting is extra.
    Same. I encourage customers to paint it themselves as the time involved in just two coats with usually dead drying time in between or two visits fitted in to other work makes it unduly expensive if I do it.

    Quote Originally Posted by Handyjack View Post
    Best to pre trim and paint all sides before installing.
    That's the best way to do it. Drying time isn't an issue as it's a small thin area that can be force dried with a heat gun in 5 to 10 minutes per coat, so the extra cost to the customer is money well spent in not having to do it themselves and ensuring long life for the door.

Similar Threads

  1. Doggy flap Installation - Wooden exterior door and fly screen door
    By Reno RSS Feed in forum GENERAL ODDS N SODS
    Replies: 0
    Last Post: 8th July 2012, 08:10 AM
  2. Bifold door installation
    By Reno RSS Feed in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETC
    Replies: 0
    Last Post: 11th December 2009, 12:40 PM
  3. aluminium sliding door installation
    By Reno RSS Feed in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETC
    Replies: 0
    Last Post: 3rd July 2009, 07:20 PM
  4. roll-a-door installation
    By Ivor in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETC
    Replies: 12
    Last Post: 15th June 2007, 09:45 AM
  5. door frame installation
    By Mack_187 in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETC
    Replies: 4
    Last Post: 11th June 2007, 06:43 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •