Page 1 of 2 12 LastLast
Results 1 to 15 of 21

Thread: New Benchtops

  1. #1
    Join Date
    Mar 2008
    Location
    perth
    Posts
    19

    Default New Benchtops

    I am looking at getting replacement bench tops for kitchen and bathroom. I would love to go for a stone (real or fake) finish but am also trying to spend the minimum to achieve a good look. As a compromise I got a quote from Granite Transformations on supplying the bench tops, surfacing and fitting them to open spaces (eg. I have to remove existing tops). They quoted $3000 for kitchen and $750 for bathroom (in any of their standard colours). This sounds expensive for the sizes and when queried on price breakdown the chip board bench tops were only $350, the rest being the labour and surface material.

    I have a quote pending from a stone (real and engineered) place but they said to expect an absolute minimum of 5k.

    Are Granite Transformations a rip off or would a high quality laminex (such as the square form range) be any cheaper?
    Last edited by venno; 1st April 2008 at 03:10 PM. Reason: Update plan

  2. #2
    Join Date
    May 2006
    Location
    Perth
    Posts
    71

    Default

    my mate was telling me he could get granite benchtops for about the same price as laminates. but its not italian granite

    i will try find out more.

  3. #3
    Join Date
    Jul 2004
    Location
    ipswich Queensland (Gods backyard)
    Age
    69
    Posts
    286

    Default

    in a laminate it would cost about $1200 (remember i said about)than you would have to fit them ,this is assuming that you have 33mm thick tops and not the drop front type ,so for that price i would assume that there is more work involved than you are telling us about ,the prices i quote are here in gods backyard
    kind regards
    tom armstrong
    www.kitcheninabox.com.au
    Flat Packed kitchens to the world

  4. #4
    Join Date
    Mar 2008
    Location
    perth
    Posts
    19

    Default

    The quote from Granite Transformations includes supply and fitment of 33mm tops wich they will then laminate with the granite sheeting so they end up being a square form edge with pencil round corners and a 40mm thickness.

    I would like to get away from my bullnose look and am also changing the size of the bench top by nocking down a raised brick section so I can have a breakfast bar (have to do that myself as well as remove existing bench top as thats not included).

    If a square form laminated 40mm top supplied and fitted will be half the cost of the fake granite I will go that route.

    cheers

  5. #5
    Join Date
    Mar 2008
    Location
    perth
    Posts
    19

    Default

    Quote Originally Posted by LegacyGT View Post
    my mate was telling me he could get granite benchtops for about the same price as laminates. but its not italian granite

    i will try find out more.

    I would be very interested in this.

  6. #6
    Join Date
    Feb 2008
    Location
    Toowoomba
    Age
    44
    Posts
    12

    Default

    Quote Originally Posted by LegacyGT View Post
    my mate was telling me he could get granite benchtops for about the same price as laminates. but its not italian granite

    i will try find out more.
    its the ceasarstone thats around about the same price, around here we use a mob called GMG stone, they use 20 mm thick which helps keep the price down.

  7. #7
    Join Date
    Mar 2008
    Location
    perth
    Posts
    19

    Default

    I have had a quote for normal stock standard laminex in bullnosefor $1500 which I must pick up and fit myself.

    I had another quote for the laminex squareform 40mm which included installation $2500.

    I finally got a quote through for granite (imported from asia), $5300, and I can't have my 200mm overhang for the breakfast bar. My cabinet may also have to be strengthened to support the weight (100kg+). There would also be an additional fee if I opt to have an undersink mount. Refitment of sink, hotplate...etc...is also at my cost. The slab is 20mm thick, to glue on additional end pieces to give a 40mm appearance is also extra.

    I went out to G.T. to look at their showroom,the stuff they use is an engineered stone sheeting that is quite thick and heavy. It looks like an engineered stone top because it is, only when you run your fingers down the underside o you realize it isn't complete slab as they don't go all the way in. The feel of the tops are good but they lack that cold sensation you get when touching a large slab of granite. The sample benchtops looked good with a 40mm square edge with pencil round chamfers. The colour range is also quite good. They gave me 6 sample pieces to take home and I intend to test all their claims regarding heat, scratches...etc...

    I am now of the opinion that G.T. may not be bad value for money after all, prices have really gone up since I last did a kitchen 10 years ago.

  8. #8
    Join Date
    Mar 2008
    Location
    perth
    Posts
    19

    Default

    I called the company who gave me the quote for real granite and asked them why they didn't include an engineered stone option. After revisiting the quote they said they made a mistake and forgot to include gst, so they said to add 10% to all their prices. They then said that all engineered stone and mid to high level granite would be a lot more expensive, and that they had merely given me the cheapest option. Well I responded with no thanks.

    I went to laminex today to discuss their squareform tops. After looking at their ones display I was very unimpressed with the feel and finish, didn't even bother pursuing that one further for the 2.5k quote.

    Meanwhile on the GT front, the product has lived up to most of their claims. I have dropped a variety of kitchen items on the samples (pass), tried to lightly score the surface with a knife (pass), and placed a hot pot from the burner onto it (fail, but the pot was dam hot). I think the surface would withstand moderate heat but certainly not straight from a full burner pot.

    By dropping 3k on the benchtop I am running out of cash for other things like the splashback and getting the doors replaced. I could just go for tiles for a splashback instead of the planned glass (was given a non measured quote of around 800 ballpark). I did want to get 2pac for doors but may have to settle for something cheaper...vinyl maybe...but I see lots of issues reported with it. Ideally I really wanted a nice colonial routed pattern to match in with all my internal doors including the kitchen pantry door.

    Any suggestions would be most welcome.

  9. #9
    Join Date
    Jul 2004
    Location
    ipswich Queensland (Gods backyard)
    Age
    69
    Posts
    286

    Default

    my suggestion would be to go back to the start and come up with a realistic budget that includes all your wish items then if you are short in the cash sense wait and save till you have enough to do the job properly rather than going with something you dont want just for the sake of how much money you have now
    kind regards
    tom armstrong
    www.kitcheninabox.com.au
    Flat Packed kitchens to the world

  10. #10
    Join Date
    May 2001
    Location
    Queanbeyan
    Age
    60
    Posts
    732

    Default

    A bit left field, but I have a mate who built formwork on top of his cupboards and then poured a concrete/stone mix to about 40mm into the form work. Once it was dried he polished it himself. It cost him about $50 worth of materials and the cost of tools.

    The benchtop looked a million dollars I thought, but he wasn't happy with it and ripped it out and was having a crack at just a laminate top.
    There was a young boy called Wyatt
    Who was awfully quiet
    And then one day
    He faded away
    Because he overused White


    Floorsanding in Canberra and Albury.....

  11. #11
    Join Date
    Dec 2007
    Location
    Brisbane
    Posts
    19

    Default

    In comparison to a new kitchen,

    I just paid 6700 inc gst for a u shape 3.6m across with 3m sides. Alot bigger than yours. This is for supply only it includes.

    - Ceasar stone benchtops choice of most colours, could be $600 cheaper if I use the most common white colour
    - Blum hinges and runners, soft close on all runners
    - Nova handles
    - 2 pac finish on all doors and draws choice of any colour, painted locally
    - Double pantry and fidge with overheads
    - 4 draws at 900 wide
    - Over head cabinets all around
    - Delivery , cabinets assembled

    The cabinets are imported but are good quality.

    Just thought I would throw that out there

  12. #12
    Join Date
    Mar 2008
    Location
    perth
    Posts
    19

    Default

    Quote Originally Posted by AIRMAN View Post
    In comparison to a new kitchen,

    I just paid 6700 inc gst for a u shape 3.6m across with 3m sides. Alot bigger than yours. This is for supply only it includes.

    - Ceasar stone benchtops choice of most colours, could be $600 cheaper if I use the most common white colour
    - Blum hinges and runners, soft close on all runners
    - Nova handles
    - 2 pac finish on all doors and draws choice of any colour, painted locally
    - Double pantry and fidge with overheads
    - 4 draws at 900 wide
    - Over head cabinets all around
    - Delivery , cabinets assembled

    The cabinets are imported but are good quality.

    Just thought I would throw that out there

    Thats a great price, wish I could get that in Perth.

  13. #13
    Join Date
    Aug 2006
    Location
    Sydney
    Age
    65
    Posts
    1,248

    Default

    Just my opinion.....granit trasfomation is the uglyest cwap you could use - besides being way over the top price wise. I

    I Love solid granite and I can handle Ceaser Stone etc but reconstituted granite is a horrid joke.

    This is a wood work forum ..how about solid wood. I got mine made and delivered 30 % cheaper than laminex. I had to cut, sand, finish and fit though.

    Attachment 70524

  14. #14
    Join Date
    Nov 2005
    Location
    Kilsyth
    Age
    66
    Posts
    300

    Default

    Quote Originally Posted by Bleedin Thumb View Post

    This is a wood work forum ..how about solid wood. I got mine made and delivered 30 % cheaper than laminex. I had to cut, sand, finish and fit though.

    Attachment 70524
    all good and fine, but you fail to mention the wood used or the finish, or how it handles day to day kitchen traffic, I expect to see a full report on the making of and installation of those lovely wood bench tops

  15. #15
    Join Date
    Jun 2007
    Location
    Perth, WA
    Posts
    67

    Default

    Quote Originally Posted by venno View Post
    Thats a great price, wish I could get that in Perth.
    Try here

    http://mcmahonauctions.com/

    They ofteh have fully assembled kitchens with granite tops around that price

Similar Threads

  1. Benchtops - only benchtops
    By sCORCH in forum KITCHENS
    Replies: 3
    Last Post: 3rd January 2008, 07:04 PM
  2. Laminated Benchtops
    By Larry LP in forum KITCHENS, BATHROOMS, THEATRES, etc
    Replies: 4
    Last Post: 4th August 2006, 10:25 PM
  3. Resurfacing benchtops
    By therockdoctor in forum KITCHENS, BATHROOMS, THEATRES, etc
    Replies: 2
    Last Post: 27th March 2006, 09:42 PM
  4. Benchtops
    By ailsa in forum KITCHENS
    Replies: 17
    Last Post: 23rd January 2004, 09:47 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •