Results 1 to 6 of 6
  1. #1
    Join Date
    Jun 2006
    Location
    adelaide
    Posts
    3

    Default Hot water system troubleshooting (bosch water wizard 780)

    ok, this is going to sound like a really stupid senario, but thanks do an alcohol fueled chili powder incident, i've had someone play a prank where they've stopped my hot water from working.

    i've tinkered with the regulator and can get it warm if the water rate is down to a trickle, but i can't get enough heat going.

    if i have the tap going, it's cold, warm, hot, warm, luke warm in the space of about 10 seconds ...

    ANYWAYS, i've found the regulator thinggy at the bottom, but that just does the water flow, i tried leaving the water running for a while but it doesn't change it much, i'm thinkin i need to find the adjuster to get more gas flowing ... just not sure how ... i've been tinkering, but to no avail as yet, any advice would be appreciated ...

  2. #2
    Join Date
    Jul 2004
    Location
    queensland
    Posts
    65

    Default

    Very dangerous country your playing in there mate !! Have you checked that your gas supply is still OK e.g valves 1/2 shut empty bottle etc?? The only other thing I would recommend would be to get a Plumber/ Gasfitter ( preferably at mates rates ) to cast a learned eye over it. Don't blow yourself up for the sake of a couple of bucks. :eek:
    Plausible deniability is the key to success

  3. #3
    Join Date
    Jul 2004
    Location
    queensland
    Posts
    65

    Default

    Double post Damm!!
    Plausible deniability is the key to success

  4. #4
    Join Date
    Jun 2006
    Location
    Brisbane
    Posts
    45

    Default

    Sounds like the same problem as I had a few months back, on the same model, but don't know how someone could do the fault.

    There's a round rubber diaphram that when water flows pushes up a small metallic rod and lets the gas flow. In my case it was badly corroded and was only partially pushing up and was resulting in a small flame, not the usual large flame inside the unit. Cost around $150 all up to have it replaced. The new ones are newer plastic stuff (polysomething) and last longer. If you do pull it apart, its quite likely it will be damaged and won't work until a new one is fitted.

    I don't think it needed to do any gas work, but at the sake of blowing yourself up I'd be using a gas fitter. 1/2 hr job.

    Have you checked for other problems first, gas supply to oven ok, gas valves on and the regulator at the meter looks normal ?

  5. #5
    Join Date
    Jun 2006
    Location
    adelaide
    Posts
    3

    Default

    hehehe, i've given up, got a guy coming out over the weekend ...

  6. #6
    Join Date
    Jun 2006
    Location
    adelaide
    Posts
    3

    Default

    thanks guys,

    ended up trackin down a friend of the family, fkn legend!

    he came out at 730, worked on it till past 10 ...

    pulled it apart, the heat issue was related to a blown thermostat which he replaced, along with the entire aluminium unit (the knobs & stuff that connects to the copper bit down the bottom) and serviced it (replacing the diaphrame & a couple other little things that come with a service)

    basically overhauled the lot, the aluminium bit was still working, but severely corroded ...

    anyways, in case anyone has similar problems, no heat is likely the thermostat

Similar Threads

  1. simplex hot water system
    By pjreno in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 0
    Last Post: 13th April 2006, 05:31 PM
  2. Hot water system - Temperature regulations
    By notrot in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 19
    Last Post: 13th September 2005, 05:54 AM
  3. Gas hot water heaters
    By Bob Willson in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 28
    Last Post: 29th March 2005, 12:16 PM
  4. hot water system
    By Gaynor in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 19
    Last Post: 1st August 2004, 06:47 PM
  5. Hot water system questions
    By Arron in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 6
    Last Post: 22nd December 2003, 11:00 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •