Results 1 to 10 of 10
  1. #1
    Join Date
    Jun 2003
    Location
    Western Sydney
    Posts
    149

    Question Question on plumbing – soft solder or silver solder or brazing

    Hi,

    I have a few questions about the differences between soft solder, silver solder and brazing in association with copper tubes / plumbing.

    Which method is used for what?


    Regards,

    Theva :confused:

  2. #2
    Join Date
    Oct 2003
    Location
    Kentucky NSW near Tamworth, Australia
    Age
    86
    Posts
    1,067

    Default

    Soft solder is ok for plumbing although a lot of plumbers use silver solder. A lot of plumbing capillary fittings come with solder incorporated in the fitting.

    Fridge mechanics use silver solder because it will take much higher pressure.

    I think they usually use brazing for general repairs on steel, brass and bronze.

  3. #3
    Join Date
    Mar 2004
    Posts
    225

    Default

    Quote Originally Posted by Theva
    Hi,

    I have a few questions about the differences between soft solder, silver solder and brazing in association with copper tubes / plumbing.

    Which method is used for what?


    Regards,

    Theva :confused:
    Soft solder is the weakest of the three, but also the cheapest. In Victoria, silver solder is used where ever copper and brass fittings are to be soldered.

    I've never heard of brazing being used on copper. Requires more heat than either soft or silver solder, perhaps too much for copper plumbing pipes.

    Having said all of that, the use of PVC instead of copper is becoming more and more widespread every day. Can't say I like it but its hard to go against the flow.(no pun intended)

    HTH,

    Mark.
    I wanted to become a brickie but my old man said "No son, learn a trade."

  4. #4
    Join Date
    Mar 2004
    Posts
    14

    Default

    Silver solder seems to be the most popular because the fittings are generally cheaper than the yorkshire ones with soft solder in them.
    I like cats but I couldn't eat a whole one :

  5. #5
    Join Date
    Jul 2004
    Location
    queensland
    Posts
    65

    Default

    Soft solder is rubbish don't use it. Silver solder is more the standard but if you want to go topshelf brazing is the choice of champions but requires Oxy/Acetylene to use whereas silver solder can be done with LPG.
    Plausible deniability is the key to success

  6. #6
    Join Date
    Jun 2003
    Location
    Western Sydney
    Posts
    149

    Default

    Thanks guys,

    Now I understand the terminology . So, it is silver solder for plumbing.

    Can anybody suggest a brand of silver solder and a suitable propane torch?

    Regards,

    Theva

  7. #7
    Join Date
    Apr 2004
    Location
    maybe next door
    Posts
    55

    Default

    Quote Originally Posted by MarkV
    but if you want to go topshelf brazing is the choice of champions but requires Oxy/Acetylene to use whereas silver solder can be done with LPG.
    You can braze copper pipe with Mapp gas (LPG and acetylene I think) and the mapp torches are about $70.00 (dont use propane/butane/LPG torch) and if you use 15% silver brazing rods on copper to copper you dont even have to use flux. Best to get a heat reflector thingo for the torch though to deflect heat all around the pipe.

  8. #8
    Join Date
    Jan 2004
    Location
    South of Adelaide
    Posts
    136

    Default

    As a former plumber I use 2% silver solder which was ample for copper to copper or copper to brass. Higher percentages of silver (which are a hell of a lot dearer) are for more refined work or perhaps what has been requested in the specifications.
    No flux is required on copper to copper provided the joints are clean. I use it (watered down) as it helps the solder to run around the joint if you are in a tight spot. Copper to brass needs flux. Ive never had much success with LPG/acetylene and prefer oxy/acetylene which burns much hotter and the job is done quicker.

    Cant say ive ever seen a 'heat reflector thingo'. If using oxy/acet keep the torch gently moving or use a slightly feathered flame so you dont overheat the copper which will cause it to crystalise and breakdown eventually, sometimes years after it has been installed. Then you have a leak somewhere hidden in the walls or under the floor. Touching the rod on the joint will tell you when its hot enough to weld.
    Jack

  9. #9
    Join Date
    Apr 2004
    Location
    maybe next door
    Posts
    55

    Default

    The heat reflector thingo clips on the end of yer torch and deflects the flame so that the opposite side of the pipe is heated also which makes it quicker/reduces heat loss. Mine was optional with the torch.

  10. #10
    Join Date
    May 2004
    Location
    Sydney
    Posts
    33

    Default

    My two cents ...

    I thought brazing was the correct thing for gas lines, as the copper is usually thicker and that is what was the "standard".

    Silver or soft solder for water lines with a LPG torch is what the plumbers I've worked with.

    Ok maybe only my 1 cent worth ;-)

    JR
    We could learn a lot from crayons: some are sharp, some are pretty, some are dull, some have weird names, and all are different colours....
    but they all exist very nicely in the same box.

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •