Results 1 to 15 of 24
Thread: JessEm Rout-R-Lift (PART 2 of 2)
-
25th October 2009, 04:42 PM #1
JessEm Rout-R-Lift (PART 2 of 2)
New Product Review
Jessem Rout-R-Lift (Part 2)
Attachment 120351
The Rout-R-Lift in Action
I fired the routers up today and cut a few dovetails and pins in some scrap Myrtle (squared up on the Kapex ). I started the router up in low speed made a cut then hit the Safety switch off. I increased the speed up to the next step and started up again, watching carefully to see if there was any discernible movement of the router due to torque. I repeated this process for each cut I made until I reached maximum speed.
To the naked eye I couldn't detect any torque movement in the router or the Rout-R-Lift within the cut-out (mind you the cutout is a very snug fit). I repeated the process with the second unit with the same result.
The dovetail joint I made was snug and required just a small amount of manual pressure to bring them together.
As a test of the winder accuracy, I didn't use my Digital Vernier to set the cutter height on the routers. I used the stock to gauge the height of the first router by placing it flat on the Gifkin template and wound the Rout-R-Lift until I had a flush height (remember though this was a test of the Rout-R-Lift adjusting winder's accuracy, normally I would have the cutter height just proud of the stock thickness to allow for cleanup).
I noted the number of turns and the position of the indicator on the main plate and without using the stock to gauge the height of the pin router bit, I just wound the 2nd unit up the same number of turns to the same position as on the first unit.
I then made the pin cuts. Whether it was planning or plain luck the d/t fit perfectly flush on both surfaces. In future, I won't rely on that method for my work and will use a vernier.
This is going to allow me to ramp up box making no end.
I'm very impressed with the Rout-R-Lift and have no hesitation recommending the unit as a best "bang for buck" for power tool accessory.
NOTE: Regarding installation as described in Part 1 of this review
1. After the units were installed in the table, I wound both up and down to their full lift range. I found that the No1 Router wouldn't raise all the way up. Discovered that my cutout was 1/8th undersize and the riser plate caught the lip of the cutout. A quick run with the hand held router fixed it.
2. While I had the units out of the table I marked out and drilled 7mm holes in the supporting lip of the cutout to match the position of the grub screws in the levelling rails so i could insert an Allen key from under the table while the units were in place.
Anyone buying a JessEm for a custom table will find final levelling much easier this way.
I hope this 2 part review has been of interest and some help.
Cheers
Sheddie
If you never made a mistake, you never made anything!
-
25th October 2009, 09:44 PM #2GOLD MEMBER
- Join Date
- Oct 2007
- Location
- vic clayton
- Posts
- 0
Thanks for the review nicely done
Some people are like slinkies - not really good for anything, but they
bring a smile to your face when pushed down the stairs .
-
26th October 2009, 10:31 AM #3Senior Member
- Join Date
- Dec 2008
- Location
- Oshawa, Ont., Canada (I wish I was in Brissie)
- Posts
- 0
I have the Rout-R-Lift FX and I love it. Easy to set up my cuts and repeat them time after time. Minute adjustment is spot on.
Jessem are about an hour's drive away in Barrie, Ont. and their customer service is second to none. Called them up on a Friday arvo looking for the template for the lift and had it in my hands Monday noon.
-
26th October 2009, 12:43 PM #4
-
26th October 2009, 04:05 PM #5
My purchasing decision
I’ve been reading with interest Shedhand’s review of his router table purchase. My Grandfather taught me that Price is what you pay and Cost is what it costs over the life of the product, so when choosing my router lifter I consulted an engineering friend to help me substantiate the price of the Woodpecker Unilift.
My friend recommended the Unilift for the following benefits (which Shedhand has identified) The FOUR riser posts (2 each side of the router) ensure no flexing compared to the two post systems, The Unilift aluminium plate is cast, then ground (ensuring a flat surface) compared to a rolled plate, and is also 66% thicker at 10mm compared to many at only 6mm. The 2 cranking positions (front and back) and the brake/lock system, together with the 3 insert rings, a starter pin, a bag full of bolts to suit fitting all routers were additional benefits that were not available in many other lifters. My other concern was the rubber belt; my shed gets stinking hot, so I worried about the life of the rubber vs. the Unilift steel chain.
So the above features together with the lifetime guarantee and a lifter that was “digital ready” convinced me to purchase the Unilift. Next week’s my birthday so I’m treating myself to a Wixey Digital Router table readout. My wife is convinced I have a birthday every month!
-
26th October 2009, 07:00 PM #6
Hi Waikune, timing BELTS in cars (working in very high temperature conditions) replaced timing CHAINS many years ago due to the chains stretching over time. The rubber belt on the JessEm lift is not subject to the same temperature extremes. The rubber beft is fibre reinforced (like vehicle timimg belts) and unlikely to stretch. Even if it did the replacement cost would be a lot cheaper than a chain. as to thickness of the main plate, mine is flat according to my engineering quality level. Drop something heavy on the cast plate and cracking or even breakage could be the result. I made the comment that I thought the UniLift was over-engineered for the average woodworker and I stand by that. However, for heavy use and larger scale routing requirements this level of engineering is probably warranted. In my case, I make boxes mostly so my setup is the optimum for me.
Cheers and thanks for the comments
SheddieLast edited by Shedhand; 26th October 2009 at 10:26 PM. Reason: retracted unsubstantiated comment.
If you never made a mistake, you never made anything!
-
26th October 2009, 07:23 PM #7.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 0
-
26th October 2009, 08:43 PM #8
-
26th October 2009, 08:50 PM #9.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 0
-
26th October 2009, 09:18 PM #10
Thank you Shedhand for this interesting and potentially cost saving review.
Much appreciated.
Cheers ,Jeff
-
26th October 2009, 09:50 PM #11
-
26th October 2009, 09:51 PM #12
-
26th October 2009, 10:08 PM #13
Hi Shedhand -You quote " I understand that there have been some problems worldwide with the UniLift chain stretching over time." If you were to look closely at a Unilift, the chain, and adjusting cam I think you will agree that your above quote just does not make any sense.
Even if it could stretch it would have to stretch one "hell of a lot" to cause a problem....and what would cause the stretch? ...for sure it's not the load in a router lifter! Perhaps I should contact Woodpeckers and see if this is the case?
I just simply wanted to express what features and benefits I considered in choosing the lifter I purchased.
-
26th October 2009, 10:10 PM #14.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 0
-
26th October 2009, 10:25 PM #15
No probs mate. No argument from me. With the purported stretching of the chain, I'm not sure, it was something some-one (I forget who) mentioned to me. But like I said, I do like the UniLift, its just a bit outside my finances which have plunged like a Beluga whale in the North Sea of late.
EDIT. I've retracted the unsubstantiated comment regarding the chain. Don't want to cause any problems for anyone.If you never made a mistake, you never made anything!
Similar Threads
-
JessEm Rout-R-Lift (PART 1 of 2)
By Shedhand in forum PRODUCT REVIEWSReplies: 16Last Post: 26th October 2009, 12:37 PM
Bookmarks