![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 6 of 6
-
21st September 2007, 09:34 PM #1
Member
- Join Date
- Sep 2007
- Location
- Black Rock, Vic
- Age
- 47
- Posts
- 38
Correcting misaligned adjoining floors
Firstly, I appologise for the barrage of posts - I have tried to search, but haven’t managed to find the answers I desire. Either my search skills are extremely poor, or I don’t know the right jargon to get decent results.
Anyway, I have decided that I’m going to pull up my existing Baltic Pine floorboards (150 x 22 or 25), and lay my new Karri boards (80 x 19) in their place.
The problem is that the existing floorboards already sit about 5mm lower than the adjoining tiled floors in the kitchen and bathroom, which means once the floorboards are replaced this difference is going to be fairly severe.
The simplest solution I can think of is to lay the Karri over a PB or ply underlay.
Is there a better/cheaper alternative to this? The area to be covered is approx 120sqm covering both levels of a double storey house.
Thanks,
Jonty
-
21st September 2007, 11:45 PM #2
You could always get the correct thickness ply and rip it down to joist width strips and pack the whole lot, but full sheet ply would give a better job.
TM
-
22nd September 2007, 10:17 AM #3
SENIOR MEMBER
- Join Date
- Aug 2005
- Location
- Victoria
- Posts
- 412
Just use masonite packing strips on each joist.
Tools
-
22nd September 2007, 11:36 AM #4
Another alternative is to simply install an aluminium ramping piece between the 2 floor levels. Ramping section is designed to bridge different floor heights and you can find it in the tile section of Bunnings - or of course tile shops.
-
22nd September 2007, 12:11 PM #5
Member
- Join Date
- Sep 2007
- Location
- Black Rock, Vic
- Age
- 47
- Posts
- 38
Thanks for the replies thus far.
TM & Tools: This sounds like a good idea, obviously a lot cheaper than installing 120sqm of ply. I imagine the masonite or ply packing should be glued and nailed/screwed to the joists, that right?
I was tending towards a red tongue (22mm) underlay accross the whole floor, which I figured would provide a very solid subfloor, albeit an expensive one. I also thought this method may provide a bit of accoustic insulation for the upper storey and some thermal insulation for the ground floor, but i'm probably fooling myself in this regard.
DD: I have contemplated some sort of quad or ramping, but I think it'll look more finished if I can match the levels up properly, also, I curretly have pretty big gaps between the doors and the floors, and the lower floor level will really accentuate this gap, which I'm trying to avoid (sorry, didn't mention the door gaps in the original post).
Cheers,
Jonty
-
24th September 2007, 08:18 AM #6
Similar Threads
-
Repairing dents in polished floors
By kkkkkkk in forum FLOORINGReplies: 5Last Post: 11th January 2007, 03:50 PM -
1920s timber floors
By eddy in forum FLOORINGReplies: 1Last Post: 28th December 2006, 08:49 PM -
Floors Floors Floors.......!
By *kate* in forum FLOORINGReplies: 12Last Post: 30th October 2005, 09:10 AM -
Timber Floors
By deliria in forum FLOORINGReplies: 2Last Post: 31st May 2005, 05:56 PM