Results 1 to 9 of 9
  1. #1
    Join Date
    May 2015
    Location
    England
    Posts
    3

    Default Triton Rta320 Insert Plate

    Hello to all.

    This is my first post on this Forum, and hope someone can help me out.

    In anticipation of buying myself a Triton TRA001 and an Insert plate RTA300 with all the bits, in a few weeks time, I want to make the hole in my router table to suit.
    So can someone give me the exact measurements of the RTA320 insert?

    Hoping you can help.
    Many Thanks

    Gray

  2. #2
    Join Date
    May 2012
    Location
    Canberra
    Posts
    122

    Default

    Ive a Kreg plate and it's a standard size.

    Another friend had the triton plate you mentioned and said it flexed too much. Not enough ribbing perhaps. He bought the Kreg and hasn't complained once, so it must be OK

    To fit, one just traces around the outside, forstner bits to cut the corners, set up the router to do the straight bits. I then use the Kreg corner adjusters, but you can simply route out the right height and trim to adjust.

  3. #3
    Join Date
    May 2015
    Location
    England
    Posts
    3

    Default

    Quote Originally Posted by Evanism View Post
    Ive a Kreg plate and it's a standard size.

    Another friend had the triton plate you mentioned and said it flexed too much. Not enough ribbing perhaps. He bought the Kreg and hasn't complained once, so it must be OK

    To fit, one just traces around the outside, forstner bits to cut the corners, set up the router to do the straight bits. I then use the Kreg corner adjusters, but you can simply route out the right height and trim to adjust.
    But will the Triton TRA001 easily fit the Kreg plate?

  4. #4
    Join Date
    Jun 2010
    Location
    Bundaberg
    Age
    54
    Posts
    160

    Default

    Kreg make their plates to suit specific router brands and to my knowledge are the only one who have specifically built a plate to suit Triton routers. It's the way I'd go for sure.

  5. #5
    Join Date
    May 2015
    Location
    England
    Posts
    3

    Default

    Quote Originally Posted by Chief Tiff View Post
    Kreg make their plates to suit specific router brands and to my knowledge are the only one who have specifically built a plate to suit Triton routers. It's the way I'd go for sure.
    Thanks a lot.
    I'll check them out.

    Gray

  6. #6
    Join Date
    May 2013
    Location
    Rockhampton QLD
    Age
    69
    Posts
    1,570

    Default

    Welcome to the forum Gray.

  7. #7
    Join Date
    Oct 2007
    Location
    Alexandra Vic
    Age
    69
    Posts
    0

    Default

    One trick for the TR series router and Kreg plate is to mount the router so that the handles are aligned with one of the diagonals of the plate, rather than straight across the long axis of the plate. This gives you extra room to remove the router and plate as an assembly if you ever have to. I also removed the passive handle from the router and store it and it's screw a drawer in the table cabinet, that gives even more wriggle room.

    I have the earlier TRA series router without the through table height winder, so I am not able to suggest which diagonal to orient the router on to give good access to the switch and speed control below the table and the winder above the table.
    I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.

  8. #8
    crowie's Avatar
    crowie is offline Life's Good, Enjoy each new day & try to encourage
    Join Date
    Dec 2009
    Location
    Faulconbridge, Lower Blue Mountains
    Age
    68
    Posts
    2,576

    Default

    G'Day & Welcome "to the Great South Land" & to a top forum "Gray".
    There are quite a few members from UK on the forum as well as across the rest of the world..
    You'll find a heap of helpful & knowledgeable blokes & ladies on the forum and for most very willing to assist as you've already found out.
    Make sure you show off your handiwork as everyone loves a photo, especially WIP [work in progress] photos with build notes.
    Enjoy the forum.
    Enjoy your woodwork.
    Cheers from On Top DownUnder, crowie

  9. #9
    Join Date
    May 2011
    Location
    FRANCE
    Age
    59
    Posts
    1,889

    Default

    Welcome to the forum

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •