Results 1 to 11 of 11
  1. #1
    Join Date
    Aug 2009
    Location
    Europe
    Posts
    2

    Red face How to repair inaccurate dovetails

    I'm new in this forum, and I need some help as I've been making dovetails which could need a little help for correct fitting .
    Is it possible to add some saw dust to the glue to fill in a ½-1 mm gap?

    TIA

    Bodker
    Denmark
    Europe

  2. #2
    Join Date
    Mar 2007
    Location
    Munruben, Qld
    Age
    84
    Posts
    0

    Default

    Hi and welcome to the forum. yes you could mix sawdust with some glue and fill the gaps but I don't think it will look too flush. You could also use CA glue to fill the gaps or Epoxy resin glue mixed with sawdust too but again I dont think it would look all that great. Give it a try and experiment with different methods. Personally I don't hand cut dovetails but use the Gifkin dovetail jig which gives a perfect dovetail joint. There are guys on the forum who do hand cut them and they do an excellent job and one of those guys may be able to give you some advice betther than I can offer. Good luck
    Reality is no background music.
    Cheers John

  3. #3
    Join Date
    Feb 2006
    Location
    Lindfield N.S.W.
    Age
    63
    Posts
    1,644

    Default

    If it really is 1mm, cut a piece of scrap (from the board or using an existing offcut) and make a veneer to push into the gap and fix it with thin CA. It still won't look flash, but it will look better than using a glue/sawdust filler for such a big gap.

    If it is a critical joint I would remake it. Either way, just chalk it up to experience - you get better at hand cutting dovetails the more of them that you do.
    Cheers

    Jeremy
    If it were done when 'tis done, then 'twere well it were done quickly

  4. #4
    Join Date
    Feb 2007
    Location
    blue mountains
    Posts
    3

    Default

    Bodker,
    Welcome to the madhouse of wood.
    You could get away with a sawdust filling if you use epoxy glue but it will look a bit rough.
    A better option is to use shims (strips) of the same wood in the gaps. Trim and plane when the glue dries. If you line them up with the grain it will almost look perfect. This is wood glued to wood so is stronger than a void full of glue. I have used this method on a scarf joint that was a bit rough.
    Regards
    John

  5. #5
    Join Date
    Feb 2007
    Location
    Adelaide
    Posts
    20

    Default

    If the length of your piece is not critical, you could lop off the offending pins or tails and start again - I have done this with a few boxes where length of width were not too important. Or, as Orraloon just said, glue in some bits matching the endgrain and cut the dovetails again closer to the right size - this could produce an almost invisible mend. I have had to do this quite a lot, and also with tenons that I have cut too slack. Filling with glue and sawdust could work okay, but it will be almost impossible to perfectly match the appearance of the end grain of the wood and so your joint lines will show quite clearly.

  6. #6
    Join Date
    Apr 2001
    Location
    Perth
    Posts
    1

    Default

    If you match end grain with end grain, it will be near impossible to pick afterwards. For face grain, match the grain carefully.

    Avoid all fillers!

    Regards from Perth

    Derek
    Visit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.

  7. #7
    Join Date
    Oct 2008
    Location
    Perth, Western Australia
    Age
    31
    Posts
    26

    Default

    Avoid all fillers!
    Lol,

    Yeah all I would do is cut a veneer and slot it in. You shouldn't have gaps, isn't that right Derek?
    "If you can't kill a zombie with it, it ain't a weapon."

  8. #8
    Join Date
    Aug 2008
    Location
    Mango Hill
    Age
    87
    Posts
    0

    Default

    [QUOTE=Bodker;1020831]I'm new in this forum, and I need some help as I've been making dovetails which could need a little help for correct fitting .
    Is it possible to add some saw dust to the glue to fill in a ½-1 mm gap?

    When I served my apprenticeship in the 50s, there was saying, " In glue and dust we put our trust" Tongue firmly in cheek!

    Colin.

  9. #9
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    2,966

    Default

    Welcome to the forum

  10. #10
    Join Date
    Aug 2009
    Location
    Europe
    Posts
    2

    Thumbs up

    Quote Originally Posted by Christos View Post
    Welcome to the forum
    Thanks an awful lot for the warm welcome and all the good advises.
    I'm sure next time I'm taking on a job like this I'll be more careful in marking and sawing the dovetails.
    The thickness of the wood is 50 mm and I did not realise a template and the router could be used for this thicknes.
    It was a lot of fun doing it by hand though, and gave me the opportunity to learn about this forum too.

    Thanks from chilly Denmark.

    Bodker

  11. #11
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    2,966

    Default

    At the beginning of this year end of last year I completed my first dovetails joint by hand since I had left school some 20 years ago. I had a bit of luck on my side as they came out straight. The gaps I left, figured that it could be a talking piece. Not able to see them unless you open the draw.

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •