![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 7 of 7
Thread: Shellawax
-
10th March 2001, 08:02 PM #1
Senior Member
- Join Date
- Mar 2000
- Location
- Melbourne, Victoria
- Posts
- 7
Shellawax
How do you apply Shellawax to a flat surface seeing it's a friction polish?
I'm only asking this out of curiosity as I've used this product on my turnings with great success, but one day I'll be turning a table leg and the bit up the top which joins the the rails is going to be flat and square.
Or should I use varnish instead?
thanks
regards
Gino
-
11th March 2001, 09:03 AM #2
I constantly use Shellawax on flat surfaces and I have succeeded in polishing by hand, however, I find it easier to wrap a rag around a ROS and use this. Works well and I wish I had started using the product earlier than I did. I used to use Organoil which took about three hours to achieve the same finish as Shellawax which takes me about two minutes.
Stupidity kills. Absolute stupidity kills absolutely.
-
16th March 2001, 04:57 PM #3
Senior Member
- Join Date
- Mar 2000
- Location
- Melbourne, Victoria
- Posts
- 7
Hi Ian
thanks for your reply and information, It's good knowing how to do these things.
I take it a ROS is an Random orbital sander?
thanks again
regards
Gino
-
16th March 2001, 05:02 PM #4
ROS Random Orbital Sander
BS Belt Sander
BS often content of BB
Have a look at http://acronymfinder.com/
Stupidity kills. Absolute stupidity kills absolutely.
-
17th March 2001, 10:39 AM #5
Gino
If using Shellawax on a flat surface with a buff it is a good idea to use a buff that has been conditioned and not a nice new clean one.
By conditioned, I mean, one that has been used before and has a slightly glased face. If all you have is a new one put some Shellawax onto a scrap piece of timber and buff it a number of times until the face of the buff starts to glaze ofer and discolour a little. You may need to do this a few time really condition it.
Leave the duff to harden for a couple of days and then you are ready to go berserk.
For Shellawax to work properly it needs to be burnt into the surface of the timber. A new buff will only pull the polish off the surface of the work where as a conditioned one will burn it into the timber. Or so goes the theory.
The best flat surface comes from using a mixture of Shellawax Cream which has been thinned with some Shellawax liquid, That way you get the penetration into the timber but also enough time to work the polish on the surface.
It is also best to allow the polish to dry on the surface before buffing otherwise streaks may appear.
For small sections like the chair leg tops rubbing by hand should suffice.
Hope this helps.
Cheers - NeilKEEP A LID ON THE GARBAGE...Report spam, scams, and inappropriate posts, PMs and Blogs.
Use the Reporticon at the bottom of all Posts, PM's and Blog entries.
-
17th March 2001, 01:27 PM #6
Thanks Neil.
Stupidity kills. Absolute stupidity kills absolutely.
-
18th March 2001, 02:12 PM #7
Senior Member
- Join Date
- Mar 2000
- Location
- Melbourne, Victoria
- Posts
- 7
Thanks Fella's much appreciate your advice
regard
Gino