Results 1 to 4 of 4
  1. #1
    Join Date
    May 2018
    Location
    Melbourne
    Posts
    27

    Default Finishing thoughts required

    Thanks to aarggh I scored the attached cupboard/sideboard. It is built like the proverbial brick outhouse of Tas oak. The finish, which appears to be a satin varnish or similar, has a few minor dings and scratches. My thinking is to sand it back to bare timber and apply a new finish.
    The question then is what finish? I have hard burnishing oil, U Beaut traditional wax and Osmo top oil clear satin which is not to say that there isn't a better option.
    I was tending towards the burnishing oil but not sure how to apply it to the recessed panels on the ends and doors.
    The door and drawer pulls will be replaced with timber ones once I find someone to turn them up for me.
    Thanks in advance.
    20230504_173052.jpg20230504_173110.jpg20230504_175740.jpg

  2. #2
    Join Date
    May 2015
    Location
    Brisbane
    Posts
    49

    Default

    I would use the burnishing oil, apply with a rubber on the flat surfaces then use a brush in the corners, end grains and hard to get at places.

  3. #3
    Join Date
    May 2007
    Location
    Sth Gippsland Vic
    Posts
    4

    Default

    Quote Originally Posted by Huon pine fan View Post
    The finish, which appears to be a satin varnish or similar, has a few minor dings and scratches. My thinking is to sand it back to bare timber and apply a new finish.
    I would avoid stripping and sanding because its such a huge job . The few dings and scratches could be made to look OK and call it patina.
    If you strip and sand your going to do all that work and end up back with what you have . The colour is going to be pretty much the same.

    If you do want to go the whole new look, don't try just sanding off the finish. That doesn't work. You have to strip with stripper then sand the raw wood back to new.

    If I was trying to revive that I would cut back the finish only by sanding with a 320 grit and oil and turps. Then give a rub down with fine steel wool. Then Id touch out the scratches with a fine brush to build them up . And give the whole piece a cover of shellac with a rubber to bring a shine back . Then wax it.
    That could look good .

    Or you could try and do a test and see if the burnishing oil sticks to the sanded cut back original finish . ( like double.d said ) That's only if I had to stick to a choice from your three cans of stuff.

    I know Osmo has a hard time of sticking to anything but Osmo so Id leave that for just doing a raw wood finish from new if you do that.

    Using the wax would only work going on top of a revived finish. If you touched out the scratches first with a fine brush and rubbed the whole thing back with fine wool then waxed it would have an effect but not good enough for what you may want I think .

  4. #4
    Join Date
    Jan 2003
    Location
    Osaka
    Posts
    346

    Default

    I'm with AusCab, no way is that in need of full strip and refinish. At most touch out scratches so they're not so obvious. Less is more.
    Semtex fixes all

Similar Threads

  1. Red gum finishing technique required
    By JasonPD in forum FINISHING
    Replies: 6
    Last Post: 23rd September 2015, 03:12 PM
  2. Finishing Services Required, Sydney
    By Lappy in forum FINISHING
    Replies: 1
    Last Post: 24th May 2010, 04:51 PM
  3. Finishing Quandry-Thoughts?
    By yabbyman in forum FINISHING
    Replies: 3
    Last Post: 27th July 2006, 02:11 PM
  4. Finishing Education Required
    By John G in forum FINISHING
    Replies: 13
    Last Post: 1st September 2002, 10:03 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •