![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 8 of 8
Thread: finish for a jarrah bar?
-
5th April 2006, 05:26 PM #1
Senior Member
- Join Date
- Jan 2004
- Location
- Melbourne
- Age
- 73
- Posts
- 0
finish for a jarrah bar?
I am just about to complete a bar made with recycled jarrah - bar, benchtop, drawers and door - internals with moisture resistant melamine. The bar will have a sink - so chance of water as well as alcohol spills. What is the best finish for this situation? Is polyurethane more practical than one of the oils?
Any comments or suggestions about the finish will be appreciated?
Regards,Smithy
-
5th April 2006, 06:12 PM #2
Unless you're setting out to splash water around and spill the alcohol:eek: , personally I would go with danish oil. I did some Jarrah bathroom cabinets in it a year or two ago and it provided a beautiful satin smooth finish that has been quite durable. Feast Watson floor finish is another alternative.
Cheers
Michael
-
5th April 2006, 06:22 PM #3
Originally Posted by gpsmith
Pour on with a finish that looks like a sheet of glass.
Alcohol & water resistant
NormellEvery day above ground is a good day
Still drinking & driving, but not at the same time
-
5th April 2006, 08:05 PM #4
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
Originally Posted by gpsmith
-
5th April 2006, 08:44 PM #5
GOLD MEMBER
- Join Date
- Jun 2003
- Location
- Sunbury, Vic
- Age
- 85
- Posts
- 632
Smithy
When you are going for your walk and collecting your paper on Friday, I will have a sample of Hard Shellac on Jarrah for you to look at. If you do not see me in the car park, call into the shop.Tom
"It's good enough" is low aim
-
5th April 2006, 08:49 PM #6
I like the Danish Oil and the Feast and Watsons Floorseal (it sounds rugged but gives a smooth low sheen finish that looks good on cabinets even though they use it on basketball courts).
I used a Mirotone 2 part polyurethane finish on my red been dining table because I wanted to be able to put hot or cold drinks on it.
It was recommended by a company that made some pretty flash commercial bars. So it had to be able to take some pretty rough treatment.
I got a heavy glassy finish on my dining table and it looked good.
Moisture, either hot or cold, hasn't hurt it but clumsy people putting heavy bowls down hard have shattered the finish. I think there is more give in the timber than the finish and the finish is brittle.
I used Floorseal on a jarrah coffee table for my 20year old daughter and it is still looking good after several years.
Because of the shattering and because I like the Floorseal look, I would prefer to use it on a jarrah bar.Scally
__________________________________________
The ark was built by an amateur
the titanic was built by professionals
-
5th April 2006, 10:23 PM #7
GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 0
Classy looking coffee table Scally and nicely grained jarrah . Is that up for a vote.
I've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
10th April 2006, 01:16 AM #8
Senior Member
- Join Date
- Jan 2004
- Location
- Melbourne
- Age
- 73
- Posts
- 0
Hard shellac for the top
Thank you all for your replies.
In a round about way (WMS) Neil has recommended hard shellac for the top of the bar and normal shellac for the vertical and non wet surfaces. This is the way that I will be going.
Thanks once again.Smithy
Similar Threads
-
Jarrah boat finish
By ubeaut in forum FINISHINGReplies: 6Last Post: 16th June 2005, 09:13 AM -
finish for reclaimed Jarrah windows
By future in forum FINISHINGReplies: 1Last Post: 13th September 2004, 11:20 PM -
Durable finish on Jarrah desk
By youvee in forum FINISHINGReplies: 9Last Post: 24th May 2004, 09:19 PM -
Best finish for Jarrah
By SteveH in forum FINISHINGReplies: 11Last Post: 19th December 2002, 10:48 PM