G'day from Sunny, Warm Canberra!

[WoodTherapy]

Nah just jokes, it's a cold, windy day and drizzling with rain here in Canberra today.

So hi there! I'm a long time stalker, first time poster. Thank you to so many people on this forum from whom I've already heeded good advice, found useful links to information I needed and benefited as much as anything from descriptions of what NOT to do/buy/try.

I thought I should get around to posting a hello message. I've made a few small projects as my skills, equipment and knowledge grow. Now that I've bought my own house and have a young family, there are a lot of tasks involving woodworking that I'd like to get on top of. And then of course there's the far more important aspect of woodworking - that I actually enjoy doing it.

The first project I worked on, partly to justify the time and expense of woodworking to SWMBO, was a shoe rack. And here's a (bad) picture:
P6020318.jpg
However, as an added challenge to myself, I didn't just want to make all the pieces as 'templates' where, say, all the vertical boards would have halving joints open on the front sides and all the horizontal boards would have halving joints open on the rear-facing sides to slot together. Instead, I chose to measure and cut each board so that the centre vertical piece would be positioned with the centre horizontal piece across it, and then vertical and horizontal boards would be alternately placed such that each of the boards have different arrangements of front/back slots and it can basically only be assembled in one order. This should maximise any errors and enforce working to tight tolerances - as I said, as an extra challenge to myself. It seemed to work. Everything came together, although it's fair to say that the last board to be slotted in was 'somewhat snug'. The 'framing' boards are just added at the end but again I had pre-cut them to their expected length so if I didn't get it right the joints would be out. What I lack in talent I perhaps make up for in being A-retentive, so I guess that worked out because the joints were square, without gaps and had flat surfaces:
P6020321.jpg

Btw, I don't care about the appearance of the end-grain etc and I've just used screws/glue on the framing joints because my mini-humans have decided that the whole thing will be painted different colours! Each of the shoe rack's 'boxes' will be a different colour. Mmmm... I expect it to look... unique.

Even a fairly simple project like this can teach you a lot. Like when you think "ahhh bugger it, I'll just use cheap pine boards from [insert "lowest prices" big box hardware store here]"
Well, if this forum has taught me nothing else, it's "You get what you pay for". So trying to build something with right angles from boards that have as much cupping in some of them as this:
P6020323.jpg
... was a bit challenging at times.

Oh well, once it's coated in 16 different kinds of kids paint nobody will be able to make their eyes look at it for long enough to notice manufacturing defects!

So in other news, I've just finished doing a 6-week basic woodworking course. I'd been trying to enrol for so long that when I'd missed it, I did different courses instead, such as "Pergolas and Decking". This actually helped develop some other basic skills such as halving joints and gave me experience with various tools and techniques. By the time I started the introduction to woodworking course, I'd pretty much outgrown it's level, I think. Or at least to start with....By then, I had some experience with my own jigsaw, circular saw (and eventually building a reliable straight-edge jig in the absence of anything else), cordless drill/driver, sander and planer. I'd also come across a cheapo ($99!) sliding compound mitre saw and starting enjoying the cleaner cuts it could give. The first week or two of any intro to woodworking course is (and IMHO probably should be) about handwork with chisels and handsaws etc. But since I'd already built the shoe rack, I had PLENTY of experience in chiselling out halving joints carefully. By the end of the course we did some basic mitre-jointed box work and I really enjoyed that. To be honest though, instead of actually making my own box in the course, I mostly used the machines available during the course which I didn't normally have access to, such as the thicknesser and table saw! I'll post some WIP photos of my box soon though.

This has all inspired me to start getting a bit more serious about the woodworking thing, especially with a bed to make for my 2yo and cots/boxes/trinkets to be made for THREE nephews/nieces to be born between November and January. So I've added a new member of my family - a beautiful baby...
P6030331.jpg

Carbatec 13" (Pseudo) Spiral head thicknesser! I'll think I'll call her CT-330X.

Oh and I also recently acquired a bunch of Triton gear: WorkCentre 2000, Table Saw, router table and TRA001 router (still unopened in it's box). That should get me going for a while.

However, it is with much shame that I admit that I have had these toys for 3 weeks and have barely even looked at them and certainly not had time to assemble and power them up!

So clearly I should stop typing, get to bed and get ready to spend some quality time this long weekend with my... [new toys and]... my family

Thanks again and I look forward to learning with you all.

[tdrumnut]

Welcome aboard and enjoy the journey.

[A Duke]

Hi Woodtherapy,
Welcome to the forum and Triton ownership.
You might find some things of interest here Triton Owners' Club (A.C.T) Inc. - Home
Hope you enjoy both.
Regards

[crowie]

G'Day & Welcome to a top forum "Woodtherapyl".
You'll find quite a few on the forum from COLD Canberra...That's one find intro & photos too....well done
You'll find a heap of helpful & knowledgeable blokes & ladies on the forum and for most very willing to assist.
Make sure you show off your handiwork as everyone loves a photo, especially WIP photos with build notes.
Enjoy the forum.
Enjoy your woodwork.
Cheers crowie

[WoodTherapy]

Thanks, Folks, for your welcomes.

A Duke, I was hoping to get along to the June meeting of the TOCACT, but it was not to be. Hopefully I'll make it to the 3 July Meeting. Thanks for the link, though. I presume you're a regular at said TOCACT meetings? If so, I'll hopefully catch up with you there!

[canvasframer]

Hi there
I am new to this forum and am hoping to learn a lot that will expand my knowledge and business.

I run a canvas printing business where I print a whole lot of custom prints onto canvas. As the business grows I am finding more and more people want custom sizes of prints and that means the framing varies widely.

First priority for me is to learn and find great suppliers of wood framing suited to canvas stretching. It is proving quite difficult!

Looking forward to getting involved, learning loads and achieving my goals.

[Christos]

Woodtherapy; Welcome to the forum.

canvasfarmer; Welcome to the forum.

[Mick0s]

Hey WoodTherapy, welcome to the forums, from one Canberran newbie to another.

I'm interested, where did you do your 6 week intro to woodworking course?
I've been looking at doing something similar, and haven't been able to find much.

Admittedly, I haven't looked very hard though.

[WoodTherapy]

The 6 week intro course I did was this one, through CIT (held at Dickson):CIT Solutions - Woodworking at Dickson

The 12 week course I'm about to start at the ANU (which is already booked out) is the fine woodworking 1 course listed here - but note there are others listed, such as the intriguing Japanese Woodworking:
Centre for Continuing Education - Visual Arts Access - Centre for Continuing Education - ANU

Not sure if these still run (dated Sep 2011):
http://www.canberrahs.act.edu.au/__d...r_20110919.pdf

Look around the other Adult Education options at Colleges such as this (Projects in Wood):
Lake Nite Learning | Program


Cheers!

[delbs]

The 12 week course I'm about to start at the ANU (which is already booked out) is the fine woodworking 1 course listed here - but note there are others listed, such as the intriguing Japanese Woodworking:
Centre for Continuing Education - Visual Arts Access - Centre for Continuing Education - ANU

Arrgghh have been wanting to get onto this for like a year now, keeps selling out before i can enroll!!!

[DaveTTC]

Wood Therapy, there is no better therapy

Welcome aboard, I like your pics and comprehensive introduction. Thanks for sharing

If you want to meet a few from the forum and some from other places who share a passion for Wood Working you may like to check this out.

https://www.woodworkforums.com/f25/ww...2014-a-170839/

At this time it looks like we will have a variety of competent woodworkers there with skills in flat work, wood turning, carving and perhaps milling.
Opportunity to spend one on one with some of these and whoever else is there and willing to share there time and expertise.

The invitation for you and whoever comes - bring some tools, bring some wood (these are optional but desired if possible) you can sell, swap, work with it or just watch others.

Mandatory if you come - a smile, willing spirit, desire to have fun learn and enjoy yourself.

Hope to see you there, if cant make it we'll see you round the forum and who knows maybe at some other event

Take Care

DaveTTC

Turning Wood Into Art