Page 1 of 2 12 LastLast
Results 1 to 15 of 20

Thread: L for leather

  1. #1
    Join Date
    Oct 2006
    Location
    Melbourne
    Posts
    0

    Default L for Leather

    Leather has been employed for writing surfaces on furniture since the seventeenth-century to provide a tactile surface on which to write. It's not only kinder on both paper and nib pens than a hard polished wood surface, but is also gentler on the writer's wrists. The types of leather most commonly used were hide (ox and cow), skiver (sheep), and less commonly, morocco (goat).

    Hides can vary from hard and smooth textured to soft and grainy, depending on the tanning procedure and are generally tough and hard wearing. Skivers are the split outer grain layer of the skins of sheep which are softer and somewhat more fragile than hides. Hides are available in fairly large dimensions and sheep being smaller animals, obviously produce smaller skins, however, both hides and skivers can be joined to cover the likes of expansive partners' desks etc. – the joins usually being disguised by tooling (embossing) over them.

    Leather is measured in ounces per square foot; one ounce being approximately 1/64" (0.4mm) thick.A single hide or skiver can vary slightly in thickness so leather weights are normally bracketed e.g. '2oz. to 3oz.' etc. The most common thickness used for writing surfaces is 4oz. to 5oz. (1/16" to 5/64" or 1.6mm to 2mm)

    Some thicker hides (5oz. to 6oz. – 5/64" to 3/32" or 2mm to 2.5mm) may require the writing surface recess to be fielded around its perimeter, which, in conjunction with the thickness of the veneer/crossbanding, provides the necessary depth to prevent the edge of the hide being an obstacle. If replacing an antique leather, the old leather should be removed prior to purchasing a replacement to ascertain if the recess is indeed fielded and thus, the type and thickness of leather required.

    Old leathers can usually be pulled off whole with care, beginning at a corner and slowly peeling upwards. If the leather was laid traditionally (with paste) then cleaning up is a simple matter of swabbing the surface with a cloth and hot water and scraping any stubborn areas. If, on the other hand, the leather was laid using a modern woodwork adhesive or contact cement, I would highly recommend hand-balling the task to someone else! Modern non-soluble adhesives are a bear to remove other than by mechanical means which can jeopardise the surrounding woodwork.

    New leathers

    I used to purchase unfinished hides (cow, buffalo and their respective calves) and then hand dye, distress and finish them to compliment the furniture they were being laid on. However, hides and skivers are available vat-dyed and 'antiqued' or, when expertly done, can be hand dyed to impart a convincing degree of wear.

    It's traditional to tool the perimeter of leathers with a combination of blind and gold decorative lines and corner motifs (a narrow blind line usually defines the extent of the fitted leather), but with embossing wheels costing anywhere between $150 and $400 each, it's unlikely the average person would possess much of a selection of tooling.


    Narrow eighteenth-century embossing wheel.


    Tooling for embossing corners.


    Blind- and gold-tooled hide.

    In the absence of professional embossing equipment, it's probably more salient to purchase ready finished and tooled loose leathers. Assuming one is purchasing a pre-tooled loose leather (sometimes called an 'inlay'), carefully measure the recess in which your chosen variety of leather will be inserted, noting any deviations of 'straight' edges and out-of-squareness. The new leather will be somewhat oversized to allow for slight inaccuracies in the recess.


    Oversize loose leather.

    If it turns out that the recess which the new leather is to be laid in is in fact out of true, then it's advisable to lay the entire oversized leather before trimming it so that the tooling remains straight irrespective of fluctuations in the shape of the recess. If the leather were pre-cut and the recess edges wandered in and out, then the leather would have to be stretched one way or another to meet the edges with the result the tooling would be maligned.

    On the other hand, if the recess is perfectly straight and accurate, then the leather can be pre-cut along all four edges prior to laying it.

    Preparing the recess

    The ground must be smooth and free of any splits or divots otherwise they will likely telegraph through the thin leather. Stabilise any splits and fill any voids with plaster filler and then sand the entire recess with coarse sandpaper. Finally remove all traces of sanding debris and dust with a stiff dry brush or a vacuum cleaner.

    Preparing the paste

    Animal glue is often considered the peerless period medium for sticking down leathers, however, even by adding a retardant to the glue, it sets far too rapidly for all but the smallest leathers such as those found on candle boards etc. Animal glue can, in conjunction with a warm iron, be used for laying baize (though it's still far from ideal) but one shouldn't attempt ironing leather!

    Quick grabbing adhesives and quick setting glues should be avoided when laying leathers: What's required is a viscous, slippery, slow setting adhesive that allows plenty of time to position the leather without fuss or panic.

    The adhesive that answers this call – and one that's been around for thousands of years – is flour paste.When mixed with water, the gluten in flour forms a translucent white paste that sets hard and yet is reversible with water should the need ever arise. The paste can be made up cold, but a superior paste results from cooking the flour and water. Modern cellulose wallpaper paste is the successor to cooked flour paste and is a perfectly good substitute, but as most households have plain flour in the kitchen and it takes but a moment to prepare…

    To make more than enough flour paste to stick a large leather down with, heat 400ml (14oz) of water in a saucepan (a few drops of food colouring or water-based stain added to the water acts as a trace that helps to avoid missing any areas when brushing it onto the furniture). Sift 30g (1oz) of flour into 200ml (7oz) of tepid water and when the consistency is smooth; slowly stir the mixture into the saucepan of hot water. Bring the mixture to the boil, stirring continuously and simmer for a few minutes until it thickens (the viscosity will further increase upon cooling). Allow the paste to cool completely before use.

    Laying a new leather

    Apply a heavy coat of paste to the ground with a stiff brush; first brushing lengthways and then crossways to ensure full coverage. Don't worry about paste flowing onto surrounding polished surfaces; it will only be briefly and can be wiped off afterwards with a damp cloth. Some of the paste's moisture will be absorbed into the wood creating uneven coverage, so allow the paste to stand for a minute before brushing the area lengthways again, replenishing the paste where necessary so a good heavy coat remains.

    With the finished side of the leather uppermost, loosely fold one end of it over the other – roughly in two – with the bottom fold extending three or four inches beyond the top fold. Supporting the leather above the pasted recess, lightly press one corner of the bottom fold into one corner of the recess. Smooth the leather down lightly with the fingers along the short side until the adjacent corners align. Begin laying the leather along the length of the recess, but resist the temptation to smooth it down yet. In the case of a pre-cut leather, ensure the edges of the leather meet the edges of the recess.

    If it's necessary to adjust the leather's position, it will be found to slide quite easily on the layer of paste. Moistening the palms of the hands (spit on them and rub them together) affords a better grip for manoeuvring the leather. Once the leather lines up smooth it down – initially with dry hands and then, using more force, with a folded dry cloth – beginning in the centre and gently squeegeeing any air pockets and glue out to the perimeter. If the recess was straight and square, the tooled lines will have self-aligned.

    If laying an oversized leather into an irregular recess, sight along the tooled lines and adjust the leather as necessary until the lines are true. Crease the leather into the edges of the recess with the rounded end of a steel ruler or similar and then carefully trim the surplus leather off with a sharp chisel held vertically.

    Run a thumb nail along the edge of the leather to tuck it down so its raw edge doesn't present an obstacle – in much the same way carpet fitters tuck the edges of fitted carpet along the skirting. Wipe the surrounding woodwork to remove any traces of paste. The paste will be dry within four to six hours.

    When giving the piece of furniture its final wax, wax the leather too.

    Some suppliers of loose leathers (no affiliations):

    Antique Leathers (UK)
    Essex Galleries (UK)
    Desk Leathers (US)
    .
    I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.


    Regards, Woodwould.

  2. #2
    Join Date
    Apr 2012
    Location
    Brisbane
    Posts
    177

    Default

    Hi WW...this is a great insight into the inlay process that I'm seeing here on my desk at the moment. However, as you have suggested, best I leave that alone! I must say, though, that you DO have a knack of making the task of replacing leather seem relatively manageable (Yes, I realize that is a subjective point!)

    I do have a beautiful little (mahogony I think?) old antique telephone table with a well preserved leather inlay. Has a few ink stains that I cant get out, but I'm happy enough to leave alone.
    Thanks for sharing your expertise here...By the way, what/ who prompted you for the dissertation on leather? Lawry

  3. #3
    Join Date
    Mar 2005
    Location
    In the shed, Melbourne
    Age
    53
    Posts
    0

    Default

    Thanks Woodwould, that'll come in very handy when I get into my next big project.
    I make things, I just take a long time.

    www.brandhouse.net.au

  4. #4
    Join Date
    Oct 2006
    Location
    Melbourne
    Posts
    0

    Default

    Quote Originally Posted by Lawry01 View Post
    By the way, what/ who prompted you for the dissertation on leather? Lawry
    Waldo asked here...

    Quote Originally Posted by Waldo View Post
    How was the leather fixed to the top, by hide glue?
    To which I replied...

    Quote Originally Posted by Woodwould View Post
    No, even with retarder in the glue, animal glue would set far too rapidly. I use a paste which allows plenty of time to position the leather. I'll be writing a separate post on the topic for my blog next week, and I'll post the same here.
    .
    I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.


    Regards, Woodwould.

  5. #5
    Join Date
    Jun 1999
    Location
    Westleigh, Sydney
    Age
    78
    Posts
    1,332

    Default

    Thanks WW. You should put your posts together as a textbook.
    Visit my website
    Website
    Facebook

  6. #6
    Join Date
    Jan 2009
    Location
    near Cooyar, (Toowoomba-ish), Qld
    Age
    60
    Posts
    0

    Default

    Thanks for that.

    We used to call goat hide 'basil' rather than 'morocco' though.
    It was pretty stretchy when wet, and was traditionally used to line or reline draught horse collars, in the part of the body of the collar which lies against the horse's shoulders.

  7. #7
    Join Date
    Oct 2006
    Location
    Melbourne
    Posts
    0

    Default

    Quote Originally Posted by Stewey View Post
    Thanks for that.

    We used to call goat hide 'basil' rather than 'morocco' though.
    It was pretty stretchy when wet, and was traditionally used to line or reline draught horse collars, in the part of the body of the collar which lies against the horse's shoulders.
    Yes, I'm familiar with basil. Goatskin can undergo various tanning processes to produce basil, levant, morocco etc.
    .
    I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.


    Regards, Woodwould.

  8. #8
    Join Date
    Aug 2011
    Location
    bilpin
    Posts
    510

    Default

    WW, any thoughts on deer hide?

  9. #9
    Join Date
    Oct 2006
    Location
    Melbourne
    Posts
    0

    Default

    Quote Originally Posted by rustynail View Post
    WW, any thoughts on deer hide?
    I used to get around in a doeskin shirt in my youth and it was exceedingly comfortable.
    .
    I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.


    Regards, Woodwould.

  10. #10
    Join Date
    Oct 2006
    Location
    Melbourne
    Posts
    0

    Default

    Quote Originally Posted by rustynail View Post
    WW, any thoughts on deer hide?
    I haven't come across deer skin with regard to leather linings, but I'm sure it would be perfectly all right given the appropriate tanning.
    .
    I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.


    Regards, Woodwould.

  11. #11
    Join Date
    Oct 2002
    Location
    NSW
    Posts
    0

    Default

    The title of your post woke up a part of my brain which vaguely recalled a rhyme my Dad used to say, which made a pun on each letter of the alphabet.

    A for horses
    B for mutton
    C for yourself
    D for dumb
    E for brick
    F for vescent
    ???
    and L for leather.

    Ahhhh, off to google and see if I can find the whole thing.

    Cheers,
    Andrew

  12. #12
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    2,966

    Default

    Very interesting read.

  13. #13
    Join Date
    Oct 2005
    Location
    Yangebup, Perth
    Posts
    0

    Default Cockney Alphabet

    Thankyou for the informative post WW, always an interesting read.

    In reply to the poem:

    As found on Wiki;

    In the 1930s, the comedy double act Clapham and Dwyer recorded the following version:
    A for 'orses (hay for horses)B for mutton (beef or mutton)C for 'th highlanders (Seaforth Highlanders)D for 'ential (deferential)E for Adam (Eve or Adam)F for 'vescence (effervescence)G for police (Chief of police)H for respect (age for respect)I for Novello (Ivor Novello)J for oranges (Jaffa oranges)K for 'ancis, (Kay Francis), or K for undressingL for leather (Hell for leather)M for 'sis (emphasis)N for 'adig (in for a dig, or infradig)O for the garden wall (over the garden wall)P for a penny (pee for a penny)Q for a song (cue for a song), or Q for billiards (cue for billiards)R for mo' (half a mo')S for you (it's for you)T for two (tea for two)U for films (UFA films)V for La France (Vive La France)W for a bob (double you for a bob)X for breakfast (eggs for breakfast)Y for Gawd's sake (why, for God's sake)Z for breezes (zephyr breezes: see West wind)[edit] Alternative versions

    There are many alternative 'definitions' offered for each letter, some of which include:
    B's for honey (bees for honey)B for you go (before you go)C for miles (see for miles)C for ships (sea for ships)C for yourself (see for yourself)D for dumb (deaf or dumb)D for 'cate (defecate)D for 'mation (deformation)D for 'ential (differential, as part of a vehicle)E for brick (heave a brick)E for 'ning Standard (Evening Standard)G for crying out loud (gee, for crying out loud)H for beauty (age before beauty)H for consent (age for consent)H for a film (age for a film)I for an eye (eye for an eye)I for the Engine (Ivor the Engine)I for or (either / or)K for 'teria (cafeteria)K for Sutherland (Kiefer Sutherland)N for 'lope (envelope)N for 'lade (enfilade)N for 'lid' (invalid)O for crying out loud (oh, for crying out loud)O for the wings of a dove (oh, for the wings of a dove)O for the rainbow (over the rainbow)P for relief (pee for relief)P for 'ming seals (performing seals)P for nanny (pee for nanny)P for a whistle (pea for a whistle)Q for chips (queue for chips)Q for a theatre (queue for a theatre)Q for tickets (queue for tickets)Q for hoursQ for a peeS for Rantzen (Esther Rantzen)S for Williams (Esther Williams)U for 'mism (euphemism)U for me (you for me)W for quits (double you for quits)Y for girlfriend (wife, or girlfriend?)Y for Heaven's sake (why, for Heaven's sake)Y for crying out loud (why, for crying out loud)Y for a husband (wife for a husband)Z for his hat (his head for his hat)
    The world is a comedy to those that think, a tragedy to those that feel.

  14. #14
    Join Date
    Oct 2007
    Location
    Yarram
    Age
    63
    Posts
    0

    Default

    Thanks WW, do you use general run of the mill supamarket flour?

  15. #15
    Join Date
    Oct 2006
    Location
    Melbourne
    Posts
    0

    Default

    Quote Originally Posted by springwater View Post
    Thanks WW, do you use general run of the mill supamarket flour?
    Absolutely. That's the glory of flour paste; it's as basic as it gets and it gets the job done.
    .
    I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.


    Regards, Woodwould.

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •