Results 1 to 12 of 12
  1. #1
    Join Date
    Jun 2009
    Location
    Elizabeth Bay / Oberon NSW
    Age
    76
    Posts
    133

    Default Need an ultra thin spanner for Carbatec Table Saw

    I have a dado stack stuck in my Carbatec TSC 10HB table saw. When I bought it second hand about 8 years ago, it never came with the thin spanner used to engage the two flats on the other side of the blade shaft. Carbatec told me the next shipment of spanners would come in late September.

    I think, but can't be sure, that I need a 28mm thin spanner to engage the flats. This I can buy as part of a set on EBay but only if I know it'll fit.

    Can anyone tell me the exact size of the spanner? Or better still, allow me to borrow it so I can change back to a single blade?

    mick

  2. #2
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default

    Once you know the size you can always buy a cheap spanner and grind/sand it to a thin profile. I had to do something similar at the mens shed, took a while but it did the job.

  3. #3
    Join Date
    Jun 2009
    Location
    Elizabeth Bay / Oberon NSW
    Age
    76
    Posts
    133

    Default

    Thanks Bob. That was plan B with Plan C involving making one from thin steel plate with hacksaw and drill.

    mick

  4. #4
    Join Date
    Feb 2016
    Location
    Canberra
    Posts
    1,183

    Default ya aint need no spanna!

    You don't need a spanner.

    Just use a piece of scrap and jam it onto the teeth of the dado - then against the front of the insert plate. Like a lever.

    This will stop the dado from turning. Just use your outside spanner on the nut.

    No need to go fancy.

  5. #5
    Join Date
    Jun 2009
    Location
    Elizabeth Bay / Oberon NSW
    Age
    76
    Posts
    133

    Default

    Quote Originally Posted by woodPixel View Post
    This will stop the dado from turning. Just use your outside spanner on the nut.
    Thanks for your input but the dado stack has been stabilized. The torque on the outside hexagonal nut is turning the shaft inside the blades. It's the shaft itself which needs held from the other side.

    mick

  6. #6
    Join Date
    Aug 2011
    Location
    bilpin
    Posts
    510

    Default

    If you are going back and forth to Oberon I can lend you one on the way through.

  7. #7
    Join Date
    Jun 2009
    Location
    Elizabeth Bay / Oberon NSW
    Age
    76
    Posts
    133

    Default

    That's incredibly kind of you and much appreciated! If I can get the dado stack out of the machine and replace it with a normal blade, Carbatec's delivery date of October would be OK.

    If the size is 28mm, I can buy a spanner to fit and save you the trouble. Could you please measure your spanner and let me know?

    mick

  8. #8
    Join Date
    Aug 2008
    Location
    Melbourne
    Age
    34
    Posts
    108

    Default

    Whole bunch of sizes here Cone Spanner

  9. #9
    Join Date
    Jun 2009
    Location
    Elizabeth Bay / Oberon NSW
    Age
    76
    Posts
    133

    Default

    Thanks Elan. I've probably posted in the wrong place because I've yet to have the size of the spanner I need confirmed. I'll have take a punt and buy a 28mm one and hope for the best.

    mick

  10. #10
    Join Date
    Jun 2003
    Location
    ...
    Posts
    1,460

    Default

    Quote Originally Posted by Glider View Post
    I'll have take a punt and buy a 28mm one and hope for the best.

    mick
    I had a look at the one I made years ago from an old spanner and mine is 29 mm opening and 3.5 mm thick. Whilst you are at it put that one and your outside spanner on longer handles as you can apply more pressure without your hands getting in the way.

    Peter.

  11. #11
    Join Date
    Aug 2008
    Location
    Melbourne
    Age
    34
    Posts
    108

    Default

    Quote Originally Posted by Glider View Post
    Thanks Elan. I've probably posted in the wrong place because I've yet to have the size of the spanner I need confirmed. I'll have take a punt and buy a 28mm one and hope for the best.

    mick
    Yeah...probably would have been better in the table saw section...

  12. #12
    Join Date
    Jun 2009
    Location
    Elizabeth Bay / Oberon NSW
    Age
    76
    Posts
    133

    Default

    Quote Originally Posted by Sturdee View Post
    I had a look at the one I made years ago from an old spanner and mine is 29 mm opening and 3.5 mm thick.
    Thanks Peter. You have to wonder why people build non-standard sizes into their designs. It's a great idea to secure the spare spanners market but not so good for repeat sales of table saws.

    The dado stack is now back in its box. Whew! At the suggestion of an engineer friend, I got under the bonnet and put a wedge between the drive belt and the pulley to stabilise the drive shaft. Bingo.

    mick

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •