![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 7 of 7
-
24th September 2007, 02:25 PM #1
Member
- Join Date
- May 2007
- Location
- Williamstown, Victoria
- Posts
- 65
Veranda post and deck bearer sharing a stirrup?
My veranda post and bearer intersect at 90 degrees and need to be supported at the one stirrup. My question is how do I acheive this:
1). Mount the veranda post in the stirrup, then attach the bearer to the veranda post (using some bracket or hanger)?
2). Mount the bearer in the stirrup then attach the veranda post to the top of the bearer?
3). Install a second stirrup near the first to mount the bearer (given the bearer will not be visible)
4). Put a cross section type join in the veranda post and bearer so 1/2 of each is supported by the stirrup and each other?
Or is there a better way?
-
24th September 2007, 02:50 PM #2
Answer usually is 1) with the mounting either a butt join using an L bracket or Pryda hanger or even mortise and tenon....or a face join (bearer face attached to post) using through bolts, coach screws or Type 17 batten screws....or....
Ours is not to reason why.....only to point and giggle.
-
24th September 2007, 07:16 PM #3
SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Sydney
- Age
- 64
- Posts
- 882
Another vote for 1)
Put the post in the stirrup and house the bearer 20mm into the post. Attach with a couple of 10/12mm galv/zp cup head bolts.
-
25th September 2007, 09:08 AM #4
SENIOR MEMBER
- Join Date
- Apr 2006
- Location
- Melbourne Victoria
- Posts
- 0
Again go with option 1 (3 votes = unanimous)
Bolts make sure they are galv, not zinc, if it is treated pine
Option 2 is also valid, but not as good.
-
25th September 2007, 11:26 AM #5
I'll be a dissenter and give the nod to option 3.
I've seen certain types of reputable stirrups fracture and snap. It has always been the type that has the thin circular shaft topped with the U shaped bracket. The weld under the bracket shears and cracks.
-
26th September 2007, 09:39 AM #6
Member
- Join Date
- May 2007
- Location
- Williamstown, Victoria
- Posts
- 65
Thanks all.
I will likely go with option 1 - I assume the bearer will need to be mounted to the side of the veranda post to bolt it? Can I connect it flush with the end of the veranda post (ie inline), as I haven't see a bracket that will allow me to do that?
If I went with option 3, which might be just as easy, do can I cement the extra stirrup in the same hole?
-
26th September 2007, 10:36 AM #7
SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Sydney
- Age
- 64
- Posts
- 882
Similar Threads
-
Attaching a wood bearer to a metal post at an angle
By WA_decker in forum DECKINGReplies: 20Last Post: 17th September 2007, 10:00 AM -
Installing decking post ( and deck nails !! )
By stuey in forum DECKINGReplies: 0Last Post: 27th August 2007, 06:28 PM -
Planing a Deck around a above ground pool - Stirrup Issues
By Decker in forum DECKINGReplies: 3Last Post: 24th April 2007, 10:35 PM -
best way to trim deck boards post nailing
By kayno in forum DECKINGReplies: 18Last Post: 1st December 2006, 08:15 AM -
attaching verandah post to deck
By cookeg in forum DECKINGReplies: 2Last Post: 9th November 2006, 07:36 AM