Page 1 of 2 12 LastLast
Results 1 to 15 of 19
  1. #1
    Join Date
    Jan 2005
    Location
    Melbourne
    Age
    65
    Posts
    4,239

    Default EEE and Traditional Wax

    I've just about worn out my search engine looking for information about using EEE Ultra Shine and Traditional Wax together.

    Is there any benefit to it and are they compatible? (I assume so but thought it best to ask, you never know )

    EDIT: Great, I seached using the words "traditional wax over EEE" and had no returns, then hundreds of unrelated stuff. After I posted this message there are three or four links at the bottom with what I wanted

    I was looking for the EEE to polish/burnish the surface so the trad wax would have a very smooth and even surface to apply to, even though it is duller than Shellac it should look better, no?

  2. #2
    Join Date
    May 1999
    Location
    Grovedale, Victoria Australia
    Age
    66
    Posts
    2

    Default

    As the EEE is an abrasive if you mixed with the trad wax you would be basically cutting the finish.

    Better to keep them apart sand the use the EEE then use the trad wax on its own
    Jim Carroll
    One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
    Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!

  3. #3
    Join Date
    Jan 2005
    Location
    Melbourne
    Age
    65
    Posts
    4,239

    Default

    Sorry Jim, I meant that I would try using the Traditional Wax AFTER I had applied the EEE, not actually mixing them together before applying them.

  4. #4
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    64
    Posts
    0

    Default

    It works for me.
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  5. #5
    Join Date
    Jan 2005
    Location
    Melbourne
    Age
    65
    Posts
    4,239

    Default

    I've done a few samples. On one side of a board I used EEE and Shellawax cream, on the other EEE and Chinese oil. The first side looks ok but the Shellawax has some waves in it from going sticky too fast (or I am too slow). The other side the Chinese oil does not want to 'go off', it may be the temperature, I'll look again in the morning.

    One more test will be EEE and Trad Wax (couldn't find mine so will have to buy some more ), the other side will be EEE and Shellac.

  6. #6
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    64
    Posts
    0

    Default

    I found that with Shellawax Cream I can only work on an area of about a square foot at any given time if I want reasonable results.

    Personally, I think that if you want to apply it over large areas you're better off using shellac instead.

    (Then again, I could be biased because I use a LOT of Shellawax on my turnings, so expect the Cream to be as easy to apply... but don't find it so.)
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  7. #7
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Hi Greg,

    I get brilliant results using EEE ultrashine and Trad wax. I use the EEE as the final cutting agent on the piece, then use 2-3 coats of Trad wax about a day apart.

    Here's a Blackwood table finished this way.

  8. #8
    Join Date
    Jan 2005
    Location
    Melbourne
    Age
    65
    Posts
    4,239

    Default

    Very nice! Do you need up to 3 coats?

  9. #9
    Join Date
    Oct 2005
    Location
    Yass
    Age
    65
    Posts
    0

    Default

    If you google "rubbing out shellac" you'll find lots of links with reference to things like pumicestone or rottenstone, which are essentially Americanisms for EEE. (Not sure if they're technically the same, but functionally are so.)

    I have found EEE quite good for the final rub out of brushed or padded shellac, which leaves a nice smooth surface for traditional wax.

    Tex

  10. #10
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Quote Originally Posted by Groggy View Post
    Very nice! Do you need up to 3 coats?
    No, but I find the finish more resilient with three coats. One coat should give a similar finish.

    Regards,

    Rob

  11. #11
    Join Date
    Jan 2005
    Location
    Melbourne
    Age
    65
    Posts
    4,239

    Default

    Thanks Rob, I'll give it a go.

  12. #12
    Join Date
    Jun 2003
    Location
    Sunbury, Vic
    Age
    85
    Posts
    632

    Default

    I do the same as LGS. Have used it over Hard Shellac and Minwax Wipe-on with great results.
    Tom

    "It's good enough" is low aim

  13. #13
    Join Date
    May 1999
    Location
    Grovedale, Victoria Australia
    Age
    66
    Posts
    2

    Default

    Greg the shellawax cream is more a friction polish needing speed and heat to work it into the peice which is why it works better on the lathe.

    Also a little is better than more.

    It could be you are applying too much and not generating enough heat to spread the paste so getting lines.
    Jim Carroll
    One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
    Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!

  14. #14
    Join Date
    Jan 2005
    Location
    Melbourne
    Age
    65
    Posts
    4,239

    Default

    Thanks Jim, the Shellawax works fine on the lathe as you suggest. I wanted to try it on a board to see how it would go. The Shellawax cream burnished up ok with a 2000 grit pad and left a pretty good finish. The Chinese wood oil did not want to go into the wood and remained on the surface.

    I picked up some more Traditional wax today and will be using that after the EEE.

  15. #15
    Join Date
    Jan 2005
    Location
    Melbourne
    Age
    65
    Posts
    4,239

    Default

    Quote Originally Posted by Chesand View Post
    I do the same as LGS. Have used it over Hard Shellac and Minwax Wipe-on with great results.
    I'll give that a test too, thanks!

Similar Threads

  1. Traditional wax
    By schaf in forum FINISHING
    Replies: 8
    Last Post: 1st June 2009, 12:43 AM
  2. Traditional Wax
    By mick61 in forum FINISHING
    Replies: 20
    Last Post: 29th January 2008, 08:01 AM
  3. Traditional Wax
    By Dion N in forum FINISHING
    Replies: 5
    Last Post: 9th December 2005, 09:03 PM
  4. Traditional Wax over EEE
    By mat in forum FINISHING
    Replies: 5
    Last Post: 17th August 2005, 02:34 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •