Results 1 to 5 of 5
  1. #1
    Join Date
    Jun 2015
    Location
    Yowie Territory, Geneva, NSW
    Age
    77
    Posts
    4

    Default Antique Boulle Clock ca1850 WIP

    Hi all... my name is Roger.
    A family heirloom,.. a fancy 19th century clock headache...
    IMGP5198c.jpgHow best to restore. My research seems to indicate its a Boulle Shelf or Mantle Clock made somewhere around 1850 in UK or France. I found a similar one in UK on internet. Its configured as a stylised shaped wooden box mounted on cast guilded legs with a marquetry facade and guilded trim. (see pic) Main issue is "Lifting marquetry" plus some staining around marquetry edges and under paint. Seems original glue after >150 years of variations in temperature and humidity (UK then Australia) has let go in a couple of places so marquetry is lifting. But not too badly damaged. So have decided to avago at restoration.
    Challenge #1
    Repair the marquetry in keeping with restoration practice. Have determined recommended practice for glue removal is warm water however the first question is "should I remove/reglue all the marquetry inserts and how?". e.g. low temp electric iron on marketry to heat/dissolve glue
    Challenge #2
    What to use? Hide or Fish glue .?.
    Challeng #3
    Cleaning. ie. tooth brush, hot water, dilute wash powder and dilute elbow grease in short bursts and minimum wood wetting via hot air drying after working each small area.
    Challenge #4
    Paint... assume water based but what recipe?

    Also need a source for antique brass escutcheon pins 1.5mm dia x 12mm long.. qty 4.

    Would very much appreciate any advice re cleaning method/materials and how to restore paint. have no intent to repaint, just clean. My thoughts are just a slow and careful warm water small area wash but after first refixing marquetry and possibly cleaning stains.
    YoHo - Fun ball bouncin time ahead.

    Any commentary at all will be appreciated.

    Roger
    Attached Images Attached Images

  2. #2
    Join Date
    Mar 2007
    Location
    Picton, NSW
    Posts
    6

    Default

    Hi Roger,
    That is a very nice clock, and may be valuable, but if you do the wrong thing, it is easy to turn a valuable antique clock into a worthless "paper weight". Don't be too hasty!

    I really do not have much advice to give you (other than to tread slowly and carefully). Unfortunately, you are a long way from Sydney. I have joined up with the Sydney chapter (Chapter 72) of the NAWCC (National Association of Watch and Clock Collectors) here in Sydney, and have seen similar clocks that have been done up to new condition and look spectacular! I know that there are folk here in Sydney who could help you out, but it is probably unreasonable for you to get down here easily. I am sure that Brisbane would have a similar group, and might be closer.

    There is a NAWCC Internet forum (based in USA) where you might get some advice.

    Does the clock work mechanically?

    Cheers

    Walesey

  3. #3
    Join Date
    Jun 2015
    Location
    Yowie Territory, Geneva, NSW
    Age
    77
    Posts
    4

    Thumbs up Boulle Clock

    Hio Walesey
    Thanks for your cautionary note. I've been so cautious that I'm yet to wind it up to hear if it ticktocks and/or hammers the bell yet. Just have to work up a bit of courage I guess.

  4. #4
    Join Date
    Jun 2015
    Location
    Yowie Territory, Geneva, NSW
    Age
    77
    Posts
    4

    Default Thread the needle and wind the clock

    Ok good people... I'm about to venture where I fear to tread... wind the clock and start the thread
    Cheers

  5. #5
    Old gunnie's Avatar
    Old gunnie is offline Old dog, learning new tricks (but slowly)
    Join Date
    Nov 2008
    Location
    Safety Bay
    Posts
    7

    Default

    Beautiful clock. How did this go?
    Some give pleasure where ever they go, others whenever they go!

Similar Threads

  1. Ambitious Boulle Marquetry Apprentice in Northern Rivers
    By boulle in forum G'day mate - THE WELCOME WAGON -Introduce yourself
    Replies: 3
    Last Post: 14th June 2015, 12:18 PM
  2. Clock mouldings for old clock
    By T5AUS in forum RESTORATION
    Replies: 1
    Last Post: 8th September 2009, 11:23 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •