Results 1 to 9 of 9
  1. #1
    Join Date
    Oct 2007
    Location
    Perth
    Posts
    6

    Default Solid Wood Island Benchtop

    Hi All,

    We are starting a kitchen reno project soon, and I'm just trying to decide what way to go with the bench tops. I'm looking into making the island bench top out of solid Jarrah (about 1000 x 1700). I can't decide between laminating some 150-200mm planks together, or maybe embarking on a massive end grain style butchers block construction with sliced up chunks of 4x4.

    Has anyone got experience with construction a large bench top in this fashion? It seems like it would be a big job, but quite possibly a lot of fun as well.

    What sort of pitfalls await me?
    What sort of glue would be appropriate for strength/waterproof/kitchen use?
    Does anyone know of any references for butcher block construction techniques?

    Any thoughts would be greatly appreciated.

  2. #2
    Join Date
    Jan 2006
    Location
    Melbourne
    Posts
    722

    Default

    I have a fantastic Jarrah bench top made of 3 big planks glued together. I'm not sure about the butcher block idea because it will get quite cut up and be very hard to keep clean and smooth. I also butchrs blocks are normally deeper than 20 or 40mm and I don't think you'd want that on a bench.

    Finally, the grain really comes out on the legths, so a normal style planked bench top would probably look better for longer. Plus you could make a matching butchers block from the left overs?

  3. #3
    Join Date
    Aug 2003
    Location
    Pambula
    Age
    59
    Posts
    5,026

    Default

    I'm about to make one of these. There are three benches, two will be edge laminated (strips of timber glued together side by side). The third will be an end grain butchers block. It's going to be 5" thick and will weigh a tonne.

    To make the end grain block, you rip long strips and glue together as for edge lamination but then you cross cut into sections which are as long as the block is to be deep, then you stand them on end and glue together, forming the checker board pattern. If you want to get serious about it, you can run some all-thread through the block and put a nut either side to protect against splitting. You want well-seasoned hardwood for this.

    Google "titebond" for glue. There is a waterproof one which I'll probably use. Or you could use an epoxy like West Systems.

    Google "butchers block" and you'll find plenty of photos. I did a bit of a search myself the other day but didn't find a lot in the way of construction details. They are pretty simple though.

    An end grain butchers block is actually a tougher surface than edge laminated or face laminated boards because the end grain is self-healing to an extent and it will absorb a lot of the damage without marking the surface.
    "I don't practice what I preach because I'm not the kind of person I'm preaching to."

  4. #4
    Join Date
    Oct 2006
    Location
    Armidale NSW
    Age
    53
    Posts
    299

    Default

    Quote Originally Posted by silentC View Post
    To make the end grain block, you rip long strips and glue together as for edge lamination but then you cross cut into sections which are as long as the block is to be deep...
    SilentC, what is the logic behind doing it this way, as opposed to just cutting up blocks of non-laminated timber?
    Cheers.

    Vernon.
    __________________________________________________
    Bite off more than you can chew and then chew like crazy.

  5. #5
    Join Date
    Sep 2006
    Location
    Behind that little door under the thicknesser...
    Posts
    44

    Default

    Quote Originally Posted by Vernonv View Post
    SilentC, what is the logic behind doing it this way, as opposed to just cutting up blocks of non-laminated timber?
    Basically it is easier/faster/less prone to alignment foul-ups to glue and clamp together as strips rather than doing it using lots of little chunks of timber.
    Ours is not to reason why.....only to point and giggle.

  6. #6
    Join Date
    Oct 2006
    Location
    Armidale NSW
    Age
    53
    Posts
    299

    Default

    OK, I think I get it now ... if you are (for example) wanting 40mm x 40mm blocks you would laminate 40 x 40 x whatever together and then cut it to the required bench top height (thickness).

    When SilentC mentioned long strips, I was thinking that he was laminating thin strips together to make up the 40 x 40
    Cheers.

    Vernon.
    __________________________________________________
    Bite off more than you can chew and then chew like crazy.

  7. #7
    Join Date
    Aug 2003
    Location
    Pambula
    Age
    59
    Posts
    5,026

    Default

    Sorry, yep 40 x 40 x whatever long. Glue up a board same width as the finished top and then dock into short boards eg. 100m for a 100mm thick bench. Then glue these together face to face to form the top.
    "I don't practice what I preach because I'm not the kind of person I'm preaching to."

  8. #8
    Join Date
    Oct 2007
    Location
    Perth
    Posts
    6

    Default

    Thanks for the construction tips SilentC... I probably would have tried gluing all the little blocks together in one hit, with disastrous results.

    Also the TiteBond III glue looks like it will do the job nicely, not sure of pricing yet though.
    http://www.titebond.com/IntroPageTB....e=94?prodcat=1

    This is an example of what I was hoping to achieve, but there are lots of other interesting examples there as well. Looks like they do some nice work.
    http://www.devoswoodworking.com/Butc...aEndGrain3.htm

    Is doing the whole island in this fashion overkill? Will it be structurally sound at those sizes? I'm looking at nearly 2 sqm (1700 long by about 1000-1200 wide), and am a bit worried about shrinkage/expansion at his size.

  9. #9
    Join Date
    Aug 2003
    Location
    Pambula
    Age
    59
    Posts
    5,026

    Default

    It can certainly be done, they have an example of something slightly smaller on that site: http://www.devoswoodworking.com/Butc...able-Maple.htm

    However, for that size, you might be better just going for the edge grain version - basically just the first step in the picture above. The idea is to have the quarter sawn edge of the timber facing up and the faces glued together, so if you look at the end of the glued up board, the growth rings are roughly perpendicular to the top of the board. This is supposed to help prevent cupping.

    I think a top that size made from end grain butcher block would be a big undertaking and would be very heavy. Very impressive though and would last forever.
    "I don't practice what I preach because I'm not the kind of person I'm preaching to."

Similar Threads

  1. Advice on my solid kitchen benchtop plans
    By Trav in forum KITCHENS
    Replies: 8
    Last Post: 25th February 2007, 03:03 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •