Results 1 to 7 of 7
  1. #1
    Join Date
    Mar 2005
    Location
    Sydney
    Posts
    12

    Default Refinishing oregon kitchen

    We have an oregon kitchen (benches, benchtops, cabinets, the works) which isn't the best material for a kitchen in my opinion, but the previous owners did it so who am I to complain?

    We last had it refinished in 2002 as the tenants gouged out one of the benches. The carpenter used some sort of Cabot's poly, but I'm not exactly sure which one.

    He didn't seal around the sink too well and consequently the timber around the sink is starting to turn black, presumably due to water intrusion.

    I'm going to do sand and it myself this time - but need some advice as to what's the best finish to use. Intergrain? Cabot's? Feast Watson? Others? Varnish? Poly? Acrylic?

    Any advice appreciated!

  2. #2
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default

    Quote Originally Posted by simopimo View Post
    We have an oregon kitchen (benches, benchtops, cabinets, the works) which isn't the best material for a kitchen in my opinion,
    We have oregon in our kitchen too and I agree it was a poor decision.

    Quote Originally Posted by simopimo View Post
    but need some advice as to what's the best finish to use. Intergrain? Cabot's? Feast Watson? Others? Varnish? Poly? Acrylic?

    Any advice appreciated!
    The first time I used a single pack poly it lasted about 2 years. The second time I used a 2-pack poly and it has lasted about 5 years but now needs redoing.

    Cheers

  3. #3
    Join Date
    Mar 2005
    Location
    Sydney
    Posts
    12

    Default

    Yeah our current poly was done in 2002 so that's about 4 years, but it's long overdue for re-coating. The black spots appeared along the timber joins and around the sink about 18 months ago, but now the black spots around the sink have become worse...

    The carpenter that did the work sanded it back to bare timber and did 2 coats of poly in the one day... which I suspect is part of the issue.

    I should have had them laminated or something!!!!


    What poly did you use last time BobL?

  4. #4
    Join Date
    Jan 2002
    Location
    Sunshine Coast, Qld
    Posts
    117

    Default

    I'd be surprised if water is penetrating the poly through the horizontal surface. It's more likely entering the end grain, possibly under the edge of the sink.

    Might pay to worry less about the type of finish than how you seal the sink edges etc.
    Rusty

  5. #5
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default

    Most of our water penetration has been following something dinging the surface, crockery or pot edge or knife etc and very little near sink edges where I really laid it on well around the seams.

    I used Cabots CFP with the accelerator - it's really meant for floors and gives a nice hard finish. It's lasted more than twice as long as single pack poly so it was worth it. Watch out for that accelerator I nearly poisoned myself on it because I was stupid and took one of my gloves off to wipe away a few dropped brush hairs and got the stuff on my skin. Fortunately once it dries on the surface its harmless.

  6. #6
    Join Date
    Dec 2004
    Location
    Brisbane
    Posts
    0

    Default

    mmmm, the material will always haunt you, as evidenced by others. Check out some marine products, pricey but good.

    If you sand back you may have to use some type of wood cleaner to get the black stuff out before finishing.

    Grain filler might also be appropriate.

    let us know how you go.
    cheers,
    conwood

  7. #7
    Join Date
    Mar 2005
    Location
    Sydney
    Posts
    12

    Default

    Thanks for the replies everyone. Does anyone think I can get away with not going back to bare timber, but just roughening the current surface where it's good, but bare timber on the dodgy parts?

    Just being lazy... oops I mean time efficient.

Similar Threads

  1. kitchen and tricky bathroom reno
    By Buttercup in forum KITCHENS
    Replies: 21
    Last Post: 3rd November 2016, 04:56 PM
  2. Kitchen from scratch.
    By Shedhand in forum KITCHENS
    Replies: 34
    Last Post: 2nd September 2006, 08:55 PM
  3. refinishing kitchen
    By Ozcruiser in forum FINISHING
    Replies: 0
    Last Post: 6th September 2005, 09:20 PM
  4. kitchen brewing up some questions
    By sandant in forum KITCHENS
    Replies: 6
    Last Post: 9th November 2004, 04:42 PM
  5. granite kitchen benching
    By sidk in forum KITCHENS
    Replies: 2
    Last Post: 28th June 2004, 12:52 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •