![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 8 of 8
Thread: Joist spacing
-
16th July 2006, 01:49 PM #1
GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 373
Joist spacing
I'm in the process of fixing up a room to use as a workshop. It was once a verandah that has been enclosed at some stage. The floor is t&g, not sure what timber ( not hardwood.) I''ve cleaned up the boards and replaced a few rotted (borers?) ones.
I'm going to lay green tongue boards over top both for appearance and for a bit of extra strength. The guideines for green tongue say to that joist spacing should be 450mm, the spacing on my floor is 600mm. (90x50 hardwood joists).
Green tongue panel is 3600x900 and will be layed with long side parallel to joists. Will this joist spacing be OK?
The condition of the joists and bearers look OK. Bearer spacing is about 1700mm so I will be adding a couple of extra bearers (LVL 150x63) so that bearers will be at (about) 1000mm centres. Room size is 2400mm x 4000mm with bearers across the smaller dimension.Geoff
The view from home
-
16th July 2006, 05:19 PM #2
Senior Member
- Join Date
- Nov 2004
- Location
- Melbourne
- Posts
- 173
just use the 22mm thick particle board for 600mm spacings instead of the 19mm. each manufacturer will have different colour tongue.
-
16th July 2006, 05:44 PM #3
Are you laying the particle board over the existing T&G or are you going directly onto the joists?
If it is over the T&G then I would think that the green tounge would be fine as it isn't spanning 600mm, it is using the T&G as the supporting structure.Now proudly sponsored by Binford Tools. Be sure to check out the Binford 6100 - available now at any good tool retailer.
-
16th July 2006, 06:58 PM #4
-
16th July 2006, 07:07 PM #5
GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 373
The green tongue will be layed over the existing t&g.
I already had the green tongue otherwise I would have gotten red tongue as suggested.Geoff
The view from home
-
16th July 2006, 09:01 PM #6
Hammer Head
- Join Date
- Jan 2005
- Location
- Sydney
- Posts
- 191
No issue with it being laid on top of T&G as the T&G is already spaning the joists. Try to screw fix through the T&G into the joists
-
18th July 2006, 02:26 AM #7
GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 373
-
19th July 2006, 12:32 AM #8
GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 373
I was planning to glue and nail, not screw because there will be no floor coverings, and I didn't want the fastenings to show.
I intend to apply a few coats of polyurethane as a finish, probably Wattyl 7008Geoff
The view from home
Similar Threads
-
Joist hangers and posts
By SIMONLEWIS in forum FLOORING, DECKING, STUMPS, etc.Replies: 3Last Post: 17th March 2006, 04:54 PM -
Filling floor joist nail holes
By Programmer in forum FLOORINGReplies: 4Last Post: 13th May 2005, 09:23 AM -
Securing joist to concrete slab
By grob in forum FLOORING, DECKING, STUMPS, etc.Replies: 14Last Post: 29th June 2003, 10:21 PM