Results 1 to 7 of 7
  1. #1
    Join Date
    Jul 2009
    Location
    Sydney
    Posts
    3

    Question Help - best way to remove Gumption abrasions from high gloss finish?

    Despite advising not to use Gumption on a mark our media cabinet, which has a white, high gloss "piano" finish, someone chose to ignore this and I'm left with the task of trying to repair it. You can easily see the abrasion in the light and I'm hoping there's a not too difficult way of doing this. If I just get the finest sandpaper available, attach it to an orbital sander, then get some sort of pad to buff it with, will that do the trick? If so, any recommendations on specific materials (sandpaper, buffing material, any sort of finish that may be required) would be hugely appreciated.
    Cheers!

  2. #2
    Join Date
    Nov 2006
    Location
    Bendigo Victoria
    Age
    80
    Posts
    4,565

    Default

    Stay away from normal "sandpaper" or wet and dry paper, all basically too coarse.

    One product to consider is Micro Mesh which goes through grits 2400 - 8000 (most wet and dry stops at 1200 or 2400). The kit linked to also includes a polishing medium and pad etc.

    Most penturners on this forum use this material to polish their pens that are made from polyester or acrylic resin.

    You may need to give a final polish with a good auto polish (not an extra-cut type).

    Or take it to a crash repairer and get them to buff it for you.

  3. #3
    Join Date
    Dec 2005
    Location
    Canberra
    Posts
    723

    Default

    Car buffing compound.

  4. #4
    Join Date
    Jul 2009
    Location
    Sydney
    Posts
    3

    Default Thanks

    Hi Big Shed and Master Splinter. Thanks for the advice. Much appreciated. Here's hoping with a bit of elbow grease, I can get this thing back to its former glossiness!

  5. #5
    Join Date
    Aug 2005
    Location
    Queensland
    Posts
    613

    Default

    Avoid any polish which contains any kind of silicone. Look specifically for " does NOT contain silicone".

    Anything which which contains silicone will cause you no end of problems when you come to refinishing anything.

  6. #6
    Join Date
    Apr 2005
    Location
    Brisbane
    Age
    54
    Posts
    85

    Default

    You may need some sandpaper (wet-dry) to take out big scratches, but if they are just 'abrasion' type marks, then forget the sand paper. Even 2000 grit WD paper will leave abrasion marks on a mirror finish.

    I second the recommendations to use car polish (not just a wax, but an actual fine polish). If you have a power sander, you can get a sheepskin pad to go over the business end, and use that for buffing, or just lots of elbow grease. Brasso actually doesn't make a bad first step polish after fine sandpaper, but doesn't quite get it to the mirror stage. One fine finishing polish I've had good luck with is Meguires Scratch X - it has a variable grade polish, so when it first comes out of the tube, it is a coarser polish, and the harder you work it, the more the particles break down into finer polish. It's a lot of work though.

    However, if you project is small enough to pick up, the best solution I've found is a loose leaf calico buffing wheel on a grinder, with a really fine polishing compound on it. If your polishing from paper, you can stop at about 600 grit and move to the polish wheel, whereas car polishes want the finish done to about 1500 before breaking out the polish. The buffing wheel gets a pretty good finish on its own - very little work, and gets it right to the mirror stage, and can be followed with the Scratch-X if you really want to be picky, or you can go straight to a nice wax. If you can't pick up your item, you might even want to consider finding a portable solution to running a calico wheel, such as a drill-based wheel.

    With any of the power tool solutions, just be careful and know when to stop. You don't want to burn through the finish. Take your time and work slowly toward the final result. Whatever you do, start in an inconspicuous place on the item, so that if anything bad happens, it won't be disastrous.
    Good things come to those who wait, and sail right past those who don't reach out and grab them.

  7. #7
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    64
    Posts
    0

    Default

    In a pinch I've also made a cutting paste from very fine grade Talcum Powder...

    ...but this is something I'd recommend practice on a sacrificial piece with first!
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

Similar Threads

  1. Making a high gloss table top finish
    By Dengue in forum FINISHING
    Replies: 5
    Last Post: 17th June 2012, 09:37 PM
  2. Super high gloss painted finish
    By Kustom Kreation in forum FINISHING
    Replies: 10
    Last Post: 23rd March 2011, 06:02 PM
  3. U Beaut wood dye high gloss finish
    By andyvan in forum FINISHING
    Replies: 7
    Last Post: 8th July 2009, 08:33 AM
  4. 2 part high gloss finish
    By urban-wombat in forum FINISHING
    Replies: 2
    Last Post: 15th July 2006, 06:01 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •