![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 5 of 5
Thread: LPG cylinder location
-
24th December 2007, 11:26 PM #1
Senior Member
- Join Date
- Oct 2007
- Location
- Hobart
- Posts
- 139
LPG cylinder location
I'm about to get my new dual fuel cooker installed - gas fitter is coming first thing in the new year.
It's rather urgent since the house doesn't presently have any working cooking facilities (just bought the place) so I haven't been as fussed with quotes etc as I otherwise would have been.
What I want to know is what are the rules for location of the LPG cylinders? These will be 2 x 9kg cylinders permanently plumbed to the cooker.
Ideally I want to put them under the ramp (concrete) from the back door. I suspect this isn't allowed however.
Preference 2 is not far from the garage entrance about 7 metres from the kitchen. It would be against the wall on the inside of a 90 degree left turn into the garage so it's unlikely a vehicle could run into the cylinders. But am I right in assuming there would be regulations against this too?
Third preference is to put them where the BBQ will be and install an outlet to "plug in" the BBQ to the same gas supply. Only reason for that is I'm trying to avoid having cylinders blocking up the path around the house.
Anyone know what the rules are for cylinder location? Only one I'm aware of is 1.5 metres from electrical appliances (air-con, water heaters etc) but I'm guessing there are lots of rules.
Natural gas isn't an option by the way but I'm told they might install pipes in the street sometime in the future.
-
24th December 2007, 11:31 PM #2
All I know is that they have to be outside & they can't be under a veranda roof.
Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
24th December 2007, 11:58 PM #3
NSW I believe they have to be on a concrete base as well
Wherever you put them make sure you have good axcess for ease of changing , their heavy little suckers.Ashore
The trouble with life is there's no background music.
-
25th December 2007, 12:54 AM #4
-
25th December 2007, 07:52 AM #5
Senior Member
- Join Date
- Jul 2007
- Location
- Sydney-south
- Posts
- 333
Depends if the cylinders are going to be exchange or in-situ filled, if they are exchange cylinders, the TOP of the cylinder has to be at least 500mm away from an ignition source, this is measured vertically up and horizontally from the valve and at the base you need 1500mm from any ignition source, you also require 1m from ANY opening into a building, including doors, vents, drains, under house etc and 150mm vertical distance to an opening window.
If in-situ fill, you will require 500mm vertical distance from ignition sources, 1500mm horizontally from the valve for the same and 3.5m from the base. The same 1m rule applies for openings into a building but you need 500mm vertical distance from the valve to an opening window.
There is restrictions for putting them under an enclosure, you need ventilation top and bottom for each cylinder, which is an area of 200cm square, or you need three sides of the enclosure open and they cant be more than 400mm in under the side of the enclosure. And the must be on a concrete base. Good luck.Plumbers were around long before Jesus was a carpenter
Similar Threads
-
Location Location
By Metal Head in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etcReplies: 9Last Post: 6th November 2007, 10:34 PM