![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 8 of 8
Thread: correct fall in guttering
-
11th September 2007, 11:55 PM #1
New Member
- Join Date
- May 2005
- Location
- Canberra
- Posts
- 2
correct fall in guttering
Hi
I am installing some new zincalume 'quad' guttering and am after some advice on the recommended fall, be it per metre, 5 metre or 10 metres of guttering. If anyone out there has installed guttering before and is aware of any 'tricks' or things to be careful of then I would appreciate your advice. Seems like a pretty straightforward thing to do though, despite 3 people quoting over $800 to install the 25m of guttering for me.
thanks in advance
Bozo
-
12th September 2007, 12:15 AM #2
Don't know if there is a standard or not but I have always dropped the gutter about 25mm to the drain points.
ie.
Put a gutter bracket on at the high end.
Put another bracket about 25mm lower at the downpipe end.
Put a string line between the two and put the remaining brackets up.
As long as there is a fall and water does not stay in the gutter then all should be fine.
-
12th September 2007, 02:06 AM #3
Standard here is 1 inch per 20 feet; about 25mm per 6m; or 42mm per 10m. Water doesn't respect national boundaries, so probably appropriate in Oz, unless 40mm or 45mm per 10m for rounder numbers.
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
12th September 2007, 10:46 AM #4
More important than the fall is enough downpipes to empty the water out of the gutter.
If you go here you will find everything you wanted to know about installing roofing, walling and gutters and were afraid to ask. Download the whole manual or the section you are interested in.
http://www.bluescopesteel.com.au/ind...F600C04FCF6B8F
-
15th September 2007, 11:43 PM #5
1:500 for eave gutters and 1:100 for box gutters according to the BCA.
Cheers
Alan
-
16th September 2007, 04:34 AM #6
Senior Member
- Join Date
- May 2007
- Location
- Darwin NT
- Posts
- 81
I have always done as DavidG does, about 20 to 25 fall in any one stretch of fascia.
I just measured off the fascia until the time we had to refix a long length. The owner got up on a ladder after we left the job and put water up there with a hose pipe. Water ponded at the wrong end. I did what I should have done in the first place and put a level on the fascia.
It was about 45mm out of level in a 9m run.
When we refixed the gutter it looked terrible, but it had to be.
Interesting Alan, that the BCA is only 10mm in 5m. Just shows how little you need.
Cheers
Bill
-
16th September 2007, 10:32 AM #7
When I was selling and erecting Ezyframe sheds which were designed by Lysaght the people that invented roofing and gutters with the Sheerline fascia type gutter we used to put it in level without fall and installed a 100 x 75 downpipe every 12 metres and didn't have any problems with water getting away.
Like I said it's all about the downpipes rather than the gutter.
-
16th September 2007, 11:28 PM #8
Similar Threads
-
Shower floor, Tile over tile; laying to fall
By Ashwood in forum TILINGReplies: 0Last Post: 21st June 2007, 12:38 PM -
re shower fall to waste
By fabdon in forum KITCHENS, BATHROOMS, THEATRES, etcReplies: 4Last Post: 18th November 2006, 09:27 AM -
Fall on paving
By Theremin in forum LANDSCAPING, GARDENING, OUTDOORSReplies: 1Last Post: 23rd July 2006, 11:31 PM