![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 8 of 8
Thread: Laying 500x500 tiles???
-
21st September 2007, 05:46 PM #1
'Just hit it harder'
- Join Date
- Mar 2007
- Location
- 'Flagstaff Hill' ADELAIDE
- Posts
- 3
Laying 500x500 tiles???
I have a large area 50sqm to lay and have bought 500x500 tiles. A friend has warned me that laying large tiles has particular problems in that, due to its size it's difficult to lay evenly. I think the problem was when he was firming down, to get good adhesive coverage beneath the tile, one end would rise up slightly and there were issues with getting the tile to be level with it's neighbors.
He is only a WW Warrior like me but I thought I would ask here for any thoughts.
I am concerned that with such a large tile if it isn't firmed down enough it will crack when walked apon!!
THANKS
.... "Don't tell him your name Pike!"
-
22nd September 2007, 12:02 AM #2
As a weekend ratbag the largest I've laid is 600 x 300, as long as you apply with a notched trowel and the floor is even it should be fairly straightforward. The only tip I'd give is keep your work area clear and make sure no tile spacers, grit or anything else slips into the adhesive. I used a longish straightedge to make sure everything went down flat and other than an errant spacer it was pretty easy. There have been no cracks and the job was on a timber floor with cement sheet underlay.
-
22nd September 2007, 05:19 AM #3
Should go fairly straightforward. Consider purchasing a "tile puck" which, when slid across the tiles as you lay them will "catch" on any raised edges, allowing you to level them before the adhesive sets.
Cheers,
Bob
-
22nd September 2007, 10:00 AM #4
SENIOR MEMBER
- Join Date
- Aug 2005
- Location
- Victoria
- Posts
- 412
I have never seen a tile puck in Australia,in fact had nevr even heard of one.But now that I have googled them, I want one! Anyone seen them in Australia?
Tools
-
22nd September 2007, 11:50 AM #5
Yeh - The tilers here have Puk's - or something very similiar.
Re 500 x 500 tiles - if the surface you are laying them on has lumps and bumps - or even gradual undulations there could be problems getting them set.
You will no doubt have to use thick bed glue if this is the case. If tiles are being put down on a concrete slab I think I would use cement mortar to set them. If glue is supporting about 75% of the tile it is unlikely they will crack under normal wear.
-
25th September 2007, 11:39 AM #6
'Just hit it harder'
- Join Date
- Mar 2007
- Location
- 'Flagstaff Hill' ADELAIDE
- Posts
- 3
Sorry been away from the board (Gastro in my girls)
Thanks all, great advice. Can you believe I was laying 50mm wall tiles once and even got a spacer underneath one of them!! So I will be careful.
Mortar sounds problematic. Is it superior to normal adhesive?
.... "Don't tell him your name Pike!"
-
25th September 2007, 11:54 PM #7
Mortar is cheaper and more reliable for laying tiles in thick bed situations.
-
1st October 2007, 01:18 AM #8
New Member
- Join Date
- Oct 2007
- Location
- USA
- Posts
- 1
how about using the Tuscan Leveling system? www.tuscanleveling.com.
Mick
Similar Threads
-
Tiles in laundry
By drummelars in forum TILINGReplies: 6Last Post: 29th December 2006, 11:55 AM -
Cutting long curve in tiles.
By dalejw in forum TILINGReplies: 10Last Post: 6th July 2006, 10:46 PM -
Tiling over existing tiles
By Andy Mac in forum TILINGReplies: 6Last Post: 8th February 2006, 03:46 PM