Page 1 of 3 123 LastLast
Results 1 to 15 of 37
  1. #1
    Join Date
    May 1999
    Location
    Tooradin,Victoria,Australia
    Age
    74
    Posts
    2,515

    Default Workshop lighting around lathes.

    As it has come up in some other threads I thought I would start another thread on this subject.

    It has been stated in another thread that it is a fact that all woodturners don't use Fluoros.
    Hi Ern,
    It is a well known fact amongst Woodturners that you don't use Fluoro's for that very reason.
    If you buy 120W Flood lights, & they don't cost that much to run, they are better for the Eyes, & a better light to see your work with.
    I'm not to sure but they have a special rating on the box as to the using Watts eg. 80W.?
    Regards,
    issatree.
    I don't know of any other woodturners (and I know a lot) that DON"T use fluoros and that includes my shed.

    We use other lights sometimes to throw light into a specific area but these are generally low energy flouros as well.

    We sometimes use incandescent floods for demos but the high wattage fluoros do a better job.

    On the odd occasion that we do have strobing (and it is very rare) a slight adjustment of speed generally eliminates it.

    Our lights are all double Fluoros of the Daylight sort by NEC.

    The walls and ceiling are all painted white and this helps with light transference immensely.

    A search on Google under "workshop lighting" gives a lot of hits and they all reccommend Flouros

  2. #2
    Join Date
    Nov 2006
    Location
    Bendigo Victoria
    Age
    80
    Posts
    4,565

    Default

    Same here , also have a 36W fluoro mounted about 3 ft above my metal lathe. Have never experienced this "strobing".

  3. #3
    Join Date
    May 1999
    Location
    Grovedale, Victoria Australia
    Age
    66
    Posts
    2

    Default

    All my lighting is fluros with a couple of spot lights for direct lighting.

    Never had any problem with strobing.

    Would like to know what others were doing when the strobing occured.

    I think and I may be wrong but the strobing may have been caused in the early days of the fluro lights when the efficiency of the ballast and starter were not so good.

    With the progress in this area the efficiency of the light is such that it does not really occur any more
    Jim Carroll
    One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
    Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!

  4. #4
    Join Date
    Oct 2004
    Location
    Oakleigh East, Sunny Vic
    Posts
    0

    Default

    I have 4 banks of double fluoros in my shed with a small Halogen spot mounted on the lathe.
    Haven't had any trouble with strobing other than some green and purple colors appearing very occasionally, and I am pretty sure that comes from the halogen globe.

    Here's a couple of quotes I found by Googling: "This safety problem is readily solved by the replacement of old style ballasts with electronic ballasts." Fluorescent lights have less adverse effects when mixed with daylight or ordinary incandescent light. Some of the modern fluorescent lights with built-in electronic ballasts are supposedly better in this regard. The light quality is still poor, but the line current flicker is eliminated."
    Cheers,
    Steck

  5. #5
    Join Date
    May 2010
    Location
    Croydon Vic
    Posts
    0

    Default

    =Jim Carroll;1171939
    Would like to know what others were doing when the strobing occured.

    I think and I may be wrong but the strobing may have been caused in the early days of the fluro lights when the efficiency of the ballast and starter were not so good.
    strobing occours because fluros flash at 50 htz(times per second) if the lathe is spinning at the same speed or a multiple of it can look like the peice is stationary it can be fixed in double fluros by putting a capacitor on only one of the ballastst whick makes the lights flash at different times, most sparkies can do this for you at a cheap price or you can buy a 50c capaciter and work it out yourself

  6. #6
    Join Date
    Jul 2005
    Location
    Flinders Shellharbour
    Posts
    0

    Default

    ]strobing occurs because fluros flash at 50 htz(times per second) if the lathe is spinning at the same speed or a multiple of it can look like the piece is stationary it can be fixed in double fluros by putting a capacitor on only one of the ballasts which makes the lights flash at different times, most sparkies can do this for you at a cheap price or you can buy a 50c capacitor and work it out yourself
    That pretty well sums it up.
    I use flouros above my lathes double tube 4 footers. With a incandescent light on one of those super flexible stands at the headstock and incandescent spotlight 150watt pointing up from the tail stock for deep hollowing.
    Flouros as general shed lighting as well and a small 6watt LED night light left on permanently for night entry. As I can be a bit messy at times and its helps the grandchildren navigate around as well.
    Inspiration exists, but it has to find you working. — Pablo Picasso


  7. #7
    Join Date
    Jun 2006
    Location
    East Warburton, Vic
    Age
    54
    Posts
    3,538

    Default

    Both my sheds have banks of Fluros, even have a couple of mini fluros as well, above the lathe and have never experienced strobing of any sort.
    Cheers

    DJ


    ADMIN

  8. #8
    Join Date
    Apr 2007
    Location
    Adelaide Hills, South Australia
    Posts
    0

    Default

    When I built my current workshop 30yrs ago was advised against fluros so installed incandescent lights.

    Now that I have replaced all the old incandescent bulbs with the new energy efficient bulbs I now have all fluros, in effect. Haven't noticed any strobing.

    .....
    Stay sharp and stay safe!

    Neil



  9. #9
    Join Date
    Jan 2004
    Location
    Towradgi
    Posts
    2

    Default

    My shed has 3 banks of double fluros, a magnetic based lamp for the lathe and the walls are white malemine and two skylights. During the day I don't need any artificial lighting.

    I have experienced the strobe effect, in the old shed, a single batten fluro. Recognised what was happening, turned the lathe of and replaced the single with a double bank of fluro.
    Pat
    Work is a necessary evil to be avoided. Mark Twain

  10. #10
    Join Date
    Feb 2006
    Location
    melbourne
    Age
    63
    Posts
    0

    Default

    G`day I use flouros and a spotty no strobe problems but have never really been happy with lighting for lathe. For a spot light what is the best you have used?
    Mick

  11. #11
    Join Date
    Jan 2002
    Location
    Melbourne, Aus.
    Age
    71
    Posts
    0

    Default

    Mick, I have an angle-able desk lamp that sits on the headstock and reaches a decent way. Also a Halogen spot on mag base that hangs off the box air scrubber overhead and shines into semi-enclosed forms. Finally I recently added a 500w paraflood but it overheats the right ear
    Cheers, Ern

  12. #12
    Join Date
    Oct 2008
    Location
    Perth
    Posts
    0

    Default

    Candles for me. Only trouble is that the air from the rapidly spinning timber sometimes blows them out.

  13. #13
    Join Date
    Nov 2006
    Location
    Bendigo Victoria
    Age
    80
    Posts
    4,565

    Default

    Picked up a couple of these in a garage sale, glued some rare earth magnets to the bottom, sits on the headstock of my wood lathe. Very stable, telescopic so you cab position it where you need the most light.

    Also have one for the metal lathe, but don't use it as often as I have a 4ft fluoro hanging 3ft above it.

  14. #14
    Join Date
    Apr 2007
    Location
    Adelaide Hills, South Australia
    Posts
    0

    Default

    Quote Originally Posted by mick61 View Post
    For a spot light what is the best you have used?
    Mick
    Planet studio lamp. Not sure if they are available any more. Screw mine to the headstock so it swivels with the headstock. From there it will reach around the largest platters I turn and into the deepest hollow forms, although I prefer to attach a LED light to my deep hollowing tools for that.

    .....
    Stay sharp and stay safe!

    Neil



  15. #15
    Join Date
    May 1999
    Location
    Tooradin,Victoria,Australia
    Age
    74
    Posts
    2,515

    Default

    Quote Originally Posted by NeilS View Post
    Planet studio lamp. Not sure if they are available any more. Screw mine to the headstock so it swivels with the headstock. From there it will reach around the largest platters I turn and into the deepest hollow forms, although I prefer to attach a LED light to my deep hollowing tools for that.

    .....
    When will we see chiselcam Neil?

Similar Threads

  1. Lighting
    By Loki429 in forum LIGHTING
    Replies: 1
    Last Post: 12th January 2007, 01:35 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •