Results 1 to 8 of 8
  1. #1
    Join Date
    May 2011
    Location
    Perth
    Posts
    0

    Default Complete amateur needs advice

    Hi, I haven't done any woodwork before but always admired it. I found a nice root and thought it would look nice if I took a slice out of it. I'm not thinking of using it for anything other than an ornamental piece (i.e., no water/heat/dirt/excessive light should go near it). I don't know what sort of wood it is, but have some pictures of my work so far - sawing it into bits and sanding to 400 grit. So now for the questions:

    1. Do I need to do anything more to the wood before finishing it?
    2. How do I get the fine sawdust particles out of the holes before finishing?
    3. What should I use to finish it? I really like the wood grain and want the natural colours and grain to stand out.
    4. How do I treat the rough edges (bark, holes, etc.) - do they need a special varnish or treatment, or should I just chop them off (and resand)?

    I hope that's enough information. Any and all advice appreciated. Thanks very much.

    Jon

  2. #2
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    64
    Posts
    0

    Default

    1. You want it to really "pop?" Sand it down further; to 800-1200 or so.
    2. Got an air-hose? Otherwise I'd simply use a fine brush and just huff and puff.
    3. Tung or Danish Oil would be my preferences; they'll darken the timber slightly and enhance the grain.
    4. Tthe bark should need no special treatment provided it's solidly attached. Just paint over it with whatever finish you're using. If it's loose and flaky, then you might want to remove it. An old toothbrush is all I use if I want to keep most of my rough edges intact. If the bark is relatively solid but looks like separating from the timber in one big piece, then you can sparingly use CA (cyano-acrylate aka "super-glue") on the bark to prevent it from parting... then apply the same finish as for the rest of the wood.
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  3. #3
    Join Date
    May 2011
    Location
    Perth
    Posts
    0

    Default

    Thank you very much for your experienced advice! Just to clarify, you use the toothbrush to spread the varnish on the rough edges, right? I was wondering how to get it into all those nooks and crannies...

    Thanks again!

    Jon

  4. #4
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    It looks like a burl, rather then a root. Often when you buy burls the bark is removed with a water blaster. The natural timber surface below the bark is exposed and its often crenulated and sometimes has an unusual spikey effect, which makes it interesting. I think its better then having an object that occassionally leaves little bits of bark around the house.

    cheers
    Arron

  5. #5
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    Another thing to remember is that whatever finish you apply to one side, you should apply to the other. This stops it warping when one side absorbs more atmospheric moisture then the other.

    I had a couple of thin burl slices like this, polished one side and fixed felt to the other. They warped after a few weeks. Varnishing both sides might have prevented this, though I cant be sure.

    Arron

  6. #6
    Join Date
    Jan 2004
    Location
    Kilmore, near Melbourne, Australia
    Age
    66
    Posts
    781

    Default

    no idea how to advise, but that is nice William Morris Thistle design fabric!
    Steve
    Kilmore (Melbourne-ish)
    Australia

    ....catchy phrase here

  7. #7
    Join Date
    Feb 2011
    Location
    Melbourne
    Posts
    206

    Default Alternative finish

    Have you tried the Livos oils. WA have three outlets and the oils are what Neil and Pam Erasmus use on their pieces.

    The oils contain waxes and are easy to use, in your case a small paint brush will get into the little nooks and crannies. Dont apply too heavily. If you wanted to maintain the "light sanded look" use the Kunos white oil.

  8. #8
    Join Date
    May 2011
    Location
    Perth
    Posts
    0

    Default

    Thanks again for all your helpful input! Is it true that a varnish will protect the wood more than an application of tung oil? Trying to decide how much of a protective coat I want versus the nice grain look. Cheers!

Similar Threads

  1. Amateur in need of advice....
    By Tizzylish in forum FINISHING
    Replies: 1
    Last Post: 17th July 2010, 03:10 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •