Results 1 to 11 of 11
  1. #1
    Join Date
    May 2006
    Location
    Roleystone, Western Australia
    Age
    56
    Posts
    4

    Default Cutting curves in fibre cement

    Does anyone have experience in cutting curves in fibre cement, e.g. villaboard / hardiflex?

    I am looking to cut some scalloped trim in the pattern shown in the picture. Any suggestions?

    Cheers

    Denis

  2. #2
    Join Date
    May 2006
    Location
    Geraldton WA
    Age
    49
    Posts
    13

    Default

    Hi Denis
    used to do a few of those found a 100 mm grinder with diamond blade made it easy if a bit messy

  3. #3
    Join Date
    Aug 2003
    Location
    Pambula
    Age
    59
    Posts
    5,026

    Default

    Yep I've found that freehand with the 4" grinder is as good a way as any. You can clean it up with a rasp, chisel or even a hand plane. Maybe you could try a jigsaw. Haven't given that a go myself but with the right blade it should work.
    "I don't practice what I preach because I'm not the kind of person I'm preaching to."

  4. #4
    Join Date
    May 2006
    Location
    Roleystone, Western Australia
    Age
    56
    Posts
    4

    Default

    Thanks Canetoad, SilentC. Is there any trick to doing it with a grinder? Do you cut along the line or grind away the waste up to the line? Probably a silly question but I just bought an angle grinder recently but have never used it.

    Denis

  5. #5
    Join Date
    Aug 2003
    Location
    Pambula
    Age
    59
    Posts
    5,026

    Default

    You'll need to get a diamond blade, which is like a thin disk of steel with diamond dust on the edges. Then you can cut into the sheet, rather than trying to grind it away. See how neat you can do it. If it's a bit rough, cut shy of the line and then clean it up with a rasp.

    For the shape you're looking at, it might really be worth giving the jigsaw a go if you've got one.
    "I don't practice what I preach because I'm not the kind of person I'm preaching to."

  6. #6
    Join Date
    Aug 2004
    Location
    Perth WA
    Posts
    355

    Default

    I'd be inclinded to use a jigsaw and use a carbourndem coated blade.

    Another way is to cut a template appropriate to and use your router (if you have one).

  7. #7
    Join Date
    May 2006
    Location
    Roleystone, Western Australia
    Age
    56
    Posts
    4

    Default

    Quote Originally Posted by rod1949
    I'd be inclinded to use a jigsaw and use a carbourndem coated blade.

    Another way is to cut a template appropriate to and use your router (if you have one).
    Thanks for the suggestions Rod. I do have a router -- what kind of bit would I use?

  8. #8
    Join Date
    Aug 2004
    Location
    Perth WA
    Posts
    355

    Default

    Quote Originally Posted by denis
    Thanks for the suggestions Rod. I do have a router -- what kind of bit would I use?
    You would have a choice of at least 3 types of bits ie;

    Straight bit - used in conjunction with the template guide that fixes into the base of the router and run against the curves template you make. or

    A Flush Trim bit or Pilot Panel bit, with these the template guide that fixes into the router is not required, as both these bits run directly against the curves template.

    You need to remember that with using a router you will not get the fine/small peaks at the top of each curve as you would if a jigsaw was used.

  9. #9
    Join Date
    May 2004
    Location
    Melbourne, Australia
    Posts
    0

    Default

    I've never tried using a router on FC sheet - and I don't think I'd like to try. But if you do could you let us know how it goes and please post some pictures of the router bit afterwards :eek:

  10. #10
    Join Date
    Aug 2004
    Location
    Perth WA
    Posts
    355

    Default

    Quote Originally Posted by chrisp
    I've never tried using a router on FC sheet - and I don't think I'd like to try. But if you do could you let us know how it goes and please post some pictures of the router bit afterwards :eek:
    Neither have I, but depending on how much has to be done a TCT bit should be ok. However I would imagine, subject to how hard and fast the router is pushed into the sheet, that the top and bottom edges of the cut would be a bit fluffy (if you know what I mean).

  11. #11
    Join Date
    May 2006
    Location
    Roleystone, Western Australia
    Age
    56
    Posts
    4

    Default

    Think I'd be a bit nervous using my regular flush trimming bit on fibre cement. I have seen references to cutting FC with a spiral saw or cutout tool, which I suppose are about the same as a router. I have come across references to special solid tungsten bits for this purpose -- on the internet, but not in the shops.

    Denis

Similar Threads

  1. Cutting a window into an internal brick wall
    By dalejw in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETC
    Replies: 4
    Last Post: 11th January 2005, 08:00 PM
  2. Compressed Fibre Cement Flooring
    By jimc in forum FLOORING
    Replies: 3
    Last Post: 8th November 2004, 10:47 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •