Results 1 to 4 of 4
  1. #1
    Join Date
    May 2007
    Location
    Gold Coast
    Posts
    0

    Default Nozzle Size For Spraying Shellac


    Have done a lot of searching and reading on this forum and other places trying to work out the right size nozzle for spaying shellac. Am going to purchase a HVLP gun (brand yet to be decided by limited budget. Suggestions welcome) that I will mainly use for this purpose. Have 7 chairs to refinish (silky oak) a medicine cabinet, dresser (english oak) and wardrobe (hoop pine) that are ready to go.

  2. #2
    Join Date
    May 2007
    Location
    Louisville, KY. U.S.A.
    Age
    71
    Posts
    6

    Default

    I'd pick a 1.5, that's a good all around size that I use a lot.
    If you get something really thick you can just reduce it a little.

    Look at the "Astro" brand guns.
    Unbelievably good quality for under $100.00.
    I use one all the time for car painting.
    I have guns costing 5 times as much and they're better but
    not by that much.
    But with any HVLP you need a lot of air,
    You need a pretty good size compressor.
    And the std 1/4" hose fittings won't allow it to spray to it's true potential. I got the 3/8" ones from Home Depot and they made a huge difference.

  3. #3
    Join Date
    Aug 2005
    Location
    kiama
    Posts
    390

    Default

    I presume you intend to finish the articles in shellac, if you are then you would also be looking at doing some french polishing to obtain a nice finish.

    If thats the case spraying the shellac won't help you much because

    * it doesn't spray well as the metho drys out so fast with the air from the gun the finish will be no better and probably a lot worse than brushing it on
    * You will also use far more material as spraying results in a 50% loss of material

    *you will have to thin the shellac a lot and that will mean you will have to put on far more coats of shellac than if you applied it with a brush, pad or other means.

    * as you are spraying chairs there will be a lot of waste doing the legs etc as a lot of the spray will miss the actual wood.

    Having said that a HVLP gun would not be a suitable gun espacially as JCCLARK has stated you need a lot of air a big hose and compressor. Unless you already have these you will be spending a lot with no great gain for your particular job.

    If you must spray a low pressure gun would be a more suitable gun to use.

    But I would apply it by hand

  4. #4
    Join Date
    May 2007
    Location
    Gold Coast
    Posts
    0

    Default

    Thanks for the feedback. I have the compressor (13cfm) but only 1/4'" fittings. Think I will give it a go by hand as I would like a high quality finish and realize over spray would also be a problem. Fantastic forum, thanks again

Similar Threads

  1. Hard Shellac Application
    By Mmcbain in forum FINISHING
    Replies: 18
    Last Post: 26th June 2006, 11:01 AM
  2. Handy Plans
    By BrisBen in forum HINTS & TIPS
    Replies: 10
    Last Post: 2nd July 2005, 09:50 PM
  3. finishing coat for shellac on red cedar
    By tallen in forum FINISHING
    Replies: 2
    Last Post: 5th February 2004, 09:17 AM
  4. Shellac for floor finish
    By JackG in forum FINISHING
    Replies: 5
    Last Post: 18th September 2002, 12:44 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •