Results 1 to 8 of 8
  1. #1
    Join Date
    Nov 2007
    Location
    australia
    Posts
    1

    Default Kitchen benchtop finish

    Hello. I have a tasmanian oak kitchen benchtop.. It has been badly finished and sprayed with an acid cure. I'm wanting to refinish it wtih oil. Can anyone please advise what sort of oil is appropriate for this use (ie. hygienic, hard-wearing and safe for food prep areas)? Also appropriate product to seal between oiled benchtop and tiled splashback? Many thanks in advance.

  2. #2
    Join Date
    Feb 2009
    Location
    Bristol, UK
    Age
    66
    Posts
    0

    Default

    Danish Oil is the stuff we use and formulated to to the job.
    Dragonfly
    No-one suspects the dragonfly!

  3. #3
    Join Date
    Feb 2011
    Location
    Melbourne
    Posts
    206

    Default Bench top

    If you are looking for a penetrating oil that you can touch up and reapply without sanding back then one suggesstion would be the Livos Kunos counter top oil. it is food safe and heat resistant to 50 degrees so coffee cups etc. If you do decide to give it a try dont sand the timber too finely as it needs to penetrate and not sit on top. you can always achieve the finer finish by sanding with a finer grit prior to the appliction of the next coat.
    If there is timber between the bench top and splash back, you can use the same product. decant any left over product to keep for rejuvenation puposes.
    Livos Australia

    <O</O

  4. #4
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Hi Reprint,

    Another product you could try would be Organoil Hard Burnishing Oil.
    Food safe, heat and moisture resistant.

    Here's my method,
    First sand to 400g, then wipe down with Turps. Let the piece dry and saturate with HBO. Allow to soak in for about 15-20 minutes, then add another coat, fairly thick. Start sanding (Random Orbital Sander) straight away. You will notice a slurry start to form as you sand. This is good. It fills the grain while you finish the piece!
    I usually go up and back along the grain for about 8 reps. Change the sanding pad to something higher (600, 800g) then repeat sanding.
    Then move up to something higher (1000, 1200g) and repeat.
    If you want, you can go higher still. I use grits up to 4000. Wipe down with a clean dry cotton cloth. You should have a silky reflective finish with great grain pattern visible.
    Important: Do not wipe the slurry off during the sanding process. If the sanding leaves the work piece dry, you can damp down the sanding pad with oil. Don't put any further oil onto the work piece surface.

    Give it a try on a scrap piece of timber and make any personal mods you think are necessary. Remember that ambient temp and humidity will change the time needed for the oil to soak into the wood.


    Regards,

    Rob

  5. #5
    Join Date
    Jan 2012
    Location
    Melbourne
    Posts
    27

    Default

    So the above options are fine if you want the natural finish of a penetrative oil and are happy to regularly re-oil it. For a harder wearing finish that will protect the timber more and require less maintenance, use a water based floor polyurethane like cabots CFP water based.

    A floor coating will be way more hard wearing than the oils mentioned above and less work.

  6. #6
    Join Date
    Mar 2003
    Location
    Newcastle
    Age
    70
    Posts
    41

    Default

    The trouble with poly on kitchen bench tops is that wear areas or any scratch let moisture penetrate the finish and cause it to flake and peel. Then you have to remove the entire finish to start again. The great thing with the oil finishes is that any little bits of damage blend in and big bits of damage can be repaired with a quick rub over with abrasive and a bit more oil.

  7. #7
    Join Date
    Jan 2012
    Location
    Melbourne
    Posts
    27

    Default

    I agree Len. But it would take A LOT of wear to reduce a bench top to that condition. I'd say bench tops usually get significantly less wear than floors - and even in high traffic areas you get many years from a flooring poly.

    I guess if you didn't have a cutting board and were continually slicing the bench, then oiling would be the best option.

  8. #8
    Join Date
    Mar 2003
    Location
    Newcastle
    Age
    70
    Posts
    41

    Default

    I took the middle path with my own bench tops and used a varnish that can be easily rubbed back and re applied. As you know with poly there is no such thing as a minor repair and I can't imagine a kitchen top that doesn't get the occasional knife dropped on it or hot frypan.
    Benches that I did 25 years ago with oil ended up almost black but I think the formula has improved since then.
    But just yesterday I was looking at a friends red ironbark benchtops which were done with hard burnishing oil two years ago and they look really good with fresh bright colour and warm wood grain surface.
    I,ve got a set of kitchen and laundry tops coming up this year so I have been thinking about it a bit. I guess I will go with the hard burnishing oil this time, the main decider being that any wear will blend in and over time develop into character/patina. Whereas my dining table I did with mirror finish poly and now in the morning sunlight every little scratch is written on the surface, so much that I will have to refinish it (this time with HBO)

Similar Threads

  1. Replies: 3
    Last Post: 4th November 2011, 08:35 PM
  2. Finish advice - beech ply kitchen benchtop
    By WortGames in forum FINISHING
    Replies: 7
    Last Post: 25th December 2007, 11:03 AM
  3. finish for kitchen benchtop
    By Ren in forum FINISHING
    Replies: 2
    Last Post: 22nd January 2003, 07:19 PM
  4. Kitchen and benchtop finish??
    By Rod Smith in forum FINISHING
    Replies: 0
    Last Post: 5th July 1999, 09:37 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •