![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 5 of 5
-
28th March 2021, 10:39 AM #1
New Member
- Join Date
- Nov 2008
- Location
- Ashfield Sydney
- Posts
- 1
plywood discolouration - mold or just stain?
Hello kind people..
I made some drawers and a work bench in the storeroom a few years ago. The top is tas oak and the drawers are hoop pine plywood.
I sealed everything with Organoil exterior decking oil because I had a tin left over lying around - the space is a store room under the stairs after all. I, perhaps naively, thought anything designed for outdoor use would be fine for an indoor job like this.
drawers.jpg
The plywood is now showing some discolouration all over the place, small reddish blotches, anywhere that didn't have something sitting on top of it.
close up 3.jpgclose up 4.jpg
I first assumed mould and set about cleaning it, then sanding back with 80 grit with the intention of removing it all and applying a new sealer.
Lots of sanding later and I can barely get into it.
It doesn't look like the mould or fungus I'm used to seeing on wood. Any chance its some chemical reaction instead?
It appears on the top plywood shelves as well. Hasn't appeared to get into the surrounding red cedar trims of the house...
Any suggestions how to manage this would be much appreciated. Hoping I don't need to rip everything out and rebuild - the drawers are working fine still.
Many thanks
Stu
-
28th March 2021, 10:47 AM #2
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
You could try some Oxalic acid - valuable from Bunnings as Rust and stain remover
https://www.bunnings.com.au/diggers-...eaner_p0960276
They seem t0 only sell it in large packs and at $30+ its not that cheap for something that you might just want to try.
Pity you are not close or I would just give you small amount.
May sure you try it out on a "not very visible spot" in case it makes it worse.
-
1st April 2021, 11:31 PM #3
Senior Member
- Join Date
- Jul 2008
- Location
- geelong
- Posts
- 72
Doesn't look like any kinda mould -More water stains. would expect them to sand out -depends how deep they have gone. Natural finishes tend to suck unless under perfect circumstances.
-
10th April 2021, 10:21 AM #4
GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 287
I second the oxalic acid suggestion. Or some other form of chemical bleach.
I caution against using 80 grit on soft plywood. You'll very quickly sand through the top layer of ply and then your staining issue will be the least of your problems.
-
10th April 2021, 07:59 PM #5
GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 610
Deck Cleaner is basically oxalic acid and will work just as well, but is much cheaper. Test in a small area first.
Apologies for unnoticed autocomplete errors.
Similar Threads
-
pink discolouration on raw timber
By kippara in forum FINISHINGReplies: 1Last Post: 31st May 2020, 07:34 PM -
Advice on removing blotches/discolouration from water based filler
By Andred in forum HINTS & TIPSReplies: 3Last Post: 25th May 2019, 10:19 AM -
Carbatec Perfect-Gloss hardener discolouration
By Lyle in forum FINISHINGReplies: 3Last Post: 10th April 2014, 08:57 AM -
DIY plywood sealer to stain??
By kroozzn62 in forum FINISHINGReplies: 7Last Post: 22nd February 2010, 10:57 PM