![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 15 of 17
Thread: haunted ute indercators?
-
31st December 2009, 08:06 PM #1
haunted ute indercators?
so iv been having trouble with me indicators.
so about a month ago it all started.
the left indicator started flashing fast. checked all the lights and they were all still working. strange i thought.
then the light on the dash for teh right indicator went dull. it was almost to dull to see but other times it was fine.
then both teh rear indicators stopped working.
now no indicators are working, teh lights on teh dash arent working but it still clicks?
any ideas?
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
31st December 2009, 08:10 PM #2
Senior Member
- Join Date
- Dec 2008
- Location
- Brisbane
- Posts
- 88
Well I reckon it's either ghosts or bad connections. My guess is ghosts.
"The training of the eyes to know when an edge is perfectly straight or a surface is flat, free from winding, and straight, is a very important part of a lad's training."
-
31st December 2009, 08:33 PM #3
but witch connections in teh switch i asume.
dam i will have to pull the dash out.
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
31st December 2009, 08:54 PM #4
Did you check to see if it was a blown globe?
-
31st December 2009, 09:28 PM #5
none of teh flashers or teh little lights in teh dash board are working its not a globe.
also i have jsut put on new led tail lights today so tehy have no globes
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
31st December 2009, 09:37 PM #6
Senior Member
- Join Date
- Dec 2008
- Location
- Brisbane
- Posts
- 88
The problems didn't start with LED indicators did they? I'm pretty sure LEDs need a different flasher unit because of the lower current draw.
"The training of the eyes to know when an edge is perfectly straight or a surface is flat, free from winding, and straight, is a very important part of a lad's training."
-
31st December 2009, 09:59 PM #7
Senior Member
- Join Date
- Sep 2006
- Location
- sinnamon park queensland
- Age
- 92
- Posts
- 14
carl,
I am totally into party mode at the present moment as tonight is my wifes birthday ( she was born on the stroke of midnight on new years eve some time ago) but I think the best plan might be to check the flasher unit before you go any further, i am also worried about the LED conversion, did this take place some where along the line while you were having this problem or did it start soon after you fitted the LED,s .
I will have to go back to the wassail department now but will try to keep abreast of your progress at intervals through the night. Happy new year and all the best for a long and prosperous future.
It's a beautiful moonlit night here in Brisbane and I hope the fire-works and revelry go safely and happily for all those who attend,
good luck and good fortune to all forum members
Witch1
-
31st December 2009, 10:10 PM #8
this problem strted over a month ago.
they stopped completely somewhere between 6 and 7am this morning.
i fited the LEDs this arvo at 4pm to replace teh broken tail/stop lights that were on it. teh whole units were plastic and it had perished and broken.
where would i find the flasher unit.
i am suposed to be going away on sunday for 3 weeks so hopefully i can track down the problem before then.
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
31st December 2009, 11:27 PM #9
Senior Member
- Join Date
- Sep 2006
- Location
- sinnamon park queensland
- Age
- 92
- Posts
- 14
carl
flasher unit may be under the dash, under the bonnet usually on the drivers side of the bulkhead, or in the steering column shroud, suggest you switch it on, and since it is apparently still clicking it should be easy enough to trace the sound to it's source. What make of car is it? I am familiar with the pommy car industry but if it was built elsewhere we might have to call in the appropriate experts from O/S.
The lucas flasher is a cylindrical unit about 65mm long and about 26mm diameter with a one hole right angled tag rivetted to the centre of one end and attached by a bolt or screw to the bulkhead or inner mudguard usually on the offside under the bonnet, the finish is usually unpolished aluminium (dull silver).
witch1.
-
1st January 2010, 07:22 AM #10
2000 holden rodeo
pretty sure it in the dash someware. iv gota pull teh dash out to fix the radio anyhow. will le you know what i find.
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
1st January 2010, 07:40 AM #11
Happy new year to all.
Another possibility is a loose earth connection. Check the lead from the battery to the chassis is not loose. Also check the battery itself is OK. Newer cars seem to loose some electrics before they stop cranking the engine.
-
1st January 2010, 08:32 AM #12
Foo
- Join Date
- Jul 2009
- Location
- Sanstone Point
- Posts
- 65
If you have fitted LEDs,you will, more than likely have to fit a resister to the circuit to,so they don't flash at a gazillion beats a minute.
-
1st January 2010, 09:19 AM #13
i think il concentrate on one problem at a time.
so i got teh flasher out.
a little black plug in thing. teh ones in teh other 2 rodeos are diferent so ill have to get a new one and see if that fits it.
why do they make it so you have to pull the vehicle apart to get to anything?
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
1st January 2010, 11:28 AM #14
Foo
- Join Date
- Jul 2009
- Location
- Sanstone Point
- Posts
- 65
Me thinks,so that you will take it to their workshops
-
1st January 2010, 12:22 PM #15