Page 1 of 2 12 LastLast
Results 1 to 15 of 21
  1. #1
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default Parker Dining table with odd coloured extensions

    Hello Everyone.

    I have a golden teak veneer MCM dining table that I’m attempting to renovate. Being a amateur I’ve taken the careful route (no electric sanding or stripper) and hand sanded the table top using 180, 240 and 320 grit, afterwards cleaning the table up with mentholated spirits and grade 2 steel wool.

    The problem is the table top is golden teak but the two end extensions are dark. I can’t put it down to fading because it’s too radical.

    I’ve tried to attach a photo to this post but can’t figure out how to do it.

    Anyway, what are my options? I did want a golden teak which is pretty typical of MCM Parker.

    Should I get the courage up and try stripping the two extensions back to the original. If that’s even possible.

    If so what stripper do I use?

    Was planning on mixing Cabots Danish Oil with Wattyl Craftsman Traditional Stain to achieve the golden teak finish.

    Any suggestions would be much appreciated.

    Von
    Attached Images Attached Images

  2. #2
    Join Date
    Jun 2015
    Location
    Sydney
    Posts
    21

    Default

    I still think that it is sun bleached, stripping it back probably won't change the colour. may need bleach the extender leaves to match.

  3. #3
    Join Date
    May 2007
    Location
    Sth Gippsland Vic
    Posts
    4

    Default

    Someone must have re done the ends darker. The ends are normally the faded parts and the leaves which dont get used as much are stored away not getting as much light so stay darker.

    Do some tests and see if the darkness strips off on a small patch . Some colour jobs are sitting on top of the old polish job. thats good if it is . Or some were striped and sanded then re stained dark . Thats not so good .

    If its been re stained dark into the wood then you have to try and see if it will cabinet scrape off or sand off after stripping .

    Just a gel stripper should be OK . Im using a new type for me . Anchor brand Professional One Shot Multi Layer Paint Stripper.
    I like it .
    I stain and get colour sorted then apply oil finish . Not mix together . What ever works though . I mix some colours with shellac if needed . Different thing .

    Rob

  4. #4
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default Here’s a better photo of the table

    I took a better photo of the table. As you can see the colour I wanted was the existing golden teak like the top and body of the table.

    I need advice on exactly how to finish this piece.

    Many thanks for your help.

    Von
    Attached Images Attached Images

  5. #5
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default

    Quote Originally Posted by pictureman View Post
    I still think that it is sun bleached, stripping it back probably won't change the colour. may need bleach the extender leaves to match.
    So how would I go about bleaching the extensions?

  6. #6
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default Here’s another photo

    I have hopefully uploaded another photo but who knows.
    Attached Images Attached Images

  7. #7
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    140

    Default

    I did not work for Parker although I did work for a "sister" company, on occasion a table with contrasting extension leaves would be requested by a customer, this may well be what you have
    if this is the case the only way the change them would be the re veneer the leaves.

    P.S. While you have it apart you may want to replace the felt runners.

  8. #8
    Join Date
    May 2007
    Location
    Sth Gippsland Vic
    Posts
    4

    Default

    Ahh it’s a draw leaf table . Just noticed the last picture .
    What I said before isn't right then . The end leaves of these live under the top and usually remain darker because of that . I thought it was a loose leaf where the ends open out and the gap left takes leaves stored somewhere else .

  9. #9
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default

    I sanded the solid table legs today and they are a golden teak colour just like the table top. It just confirmed that I’d rather finish the table a golden teak colour.

    So what’s involved with bleaching the extensions? Can a rank amateur do it?

    many thanks
    Von

  10. #10
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default

    Golly, I hadn’t notices anything wrong with the runners. And there’s another thing to fix.

  11. #11
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default

    Quote Originally Posted by auscab View Post
    Ahh it’s a draw leaf table . Just noticed the last picture .
    What I said before isn't right then . The end leaves of these live under the top and usually remain darker because of that . I thought it was a loose leaf where the ends open out and the gap left takes leaves stored somewhere else .
    Yes these extensions have never seen daylight.

    My better half told me not to worry about it as the table will never be extended but I’d like to do the job right. I’m not going to add a finish until I’ve exhausted other options.

  12. #12
    Join Date
    Dec 2020
    Location
    Australia
    Posts
    11

    Default

    Quote Originally Posted by China View Post
    I did not work for Parker although I did work for a "sister" company, on occasion a table with contrasting extension leaves would be requested by a customer, this may well be what you have
    if this is the case the only way the change them would be the re veneer the leaves.

    P.S. While you have it apart you may want to replace the felt runners.
    Sorry, didn't read your post properly. You said "felt runners". Where should the felt runners be located under the table?

  13. #13
    Join Date
    Aug 2004
    Location
    Perth WA
    Posts
    355

    Default

    Parker Furniture eh. So that would be veneered chipboard that people paid a fortune for?
    Experienced in removing the tree from the furniture

  14. #14
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    140

    Default

    Yes usually a strip of thin felt under the main top on each side to stop the extension pieces rubbing timber to timber

  15. #15
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    140

    Default

    rod194 Correct now they sell for more than the did when new

Similar Threads

  1. Parker Extension Dining Table
    By Mandapi in forum RESTORATION
    Replies: 5
    Last Post: 27th January 2015, 05:22 PM
  2. Parker dining table stripping and refinishing
    By meggg in forum FINISHING
    Replies: 8
    Last Post: 15th December 2014, 03:31 PM
  3. Professional help needed for Parker dining table
    By evilwillow in forum FINISHING
    Replies: 3
    Last Post: 19th March 2012, 08:57 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •