![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 5 of 5
Thread: Heat proof finish
-
17th August 2012, 09:24 PM #1
Heat proof finish
From a scrap piece of Tassie Oak left over from the top of an entertainment unit I'd built a few months ago I made my wife a table centre piece to place hot out-of-the-oven corning-ware serving dishes. Now I'm stuck as I've no idea what finish to use to stand searing hot containers on. My first thought was to add a cork top but that'll totally hide the TO grain. So I've stalled at this stage and the local builder's hardware guys are of no help whatsoever.
Appreciate all and any advice or suggestions to help solve my predicament.
Cheers, Ian.
-
17th August 2012, 09:59 PM #2
Hi Ian,
I'm not sure that anything but solid plastic finish will handle searing heat, but I have used Organoil Hard Burnishing oil on a Kitchen bench which has had hot pots, steaming lids and hot casserole dishes placed on it for the last 7 years, with no evidence of marking. Its fluid resistant too. The finish mustbe applied as per the directions for the protection to work, but work it does! Cleans up with Spray and Wipe too. Some will say it's not worth the bother, but I can tell you it really does work if done properly.
Regards,
Rob
-
19th August 2012, 01:37 PM #3
Hi Rob,
Thank you for your prompt response.
Yes, you've hit the nail right on the head - what you've described about your kitchen bench top is exactly what I was seeking. There is a local supplier here on the NSW Central Coast of Organoil products so I'll go visit them tomorrow.
PS. "Damn Fine Furniture" is an understatement! Wonderful craftsmanship.
Cheers, Ian.
-
22nd August 2012, 10:49 PM #4
Of course the qusetion is how hot is hot.
sooner or later things get hot enough to burn almsot any finish you can think of.
Single pack polly is pretty uselss and melts are pretty low temperatures.
some of the finishes such as the two packs and epoxies may tolerate more heat.
all th real heatprrof paints and Industrial coatings are silicon or teflon or whatever bassed.
but then yoi get to the problem of damage occuring to the wood below, often the moisture in the wood boils and either accumulates under, ruptures the finish or cracks the wood.
My thaought are to treat the item like a cutting board, fine sand it and then treat it with clear parifin oil.
That way when it does start looking a bit rough you can have at it with the sander and re-oil......all good.
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
23rd August 2012, 08:04 PM #5
SENIOR MEMBER
- Join Date
- Dec 2011
- Location
- Buderim qld
- Posts
- 17
A trivet to put the hot pots on sounds like the go to me. Otherwise you are asking for trouble. Another project for you to tackle.
Similar Threads
-
suggestions for strong & water proof finish
By clandor in forum FINISHINGReplies: 3Last Post: 15th July 2011, 09:46 PM -
Heat proof material
By Tubbster in forum NOTHING AT ALL TO DO WITH RENOVATIONReplies: 6Last Post: 10th March 2009, 09:35 AM -
heat resistant finish
By julianx in forum FINISHINGReplies: 4Last Post: 1st July 2004, 10:32 PM