Results 1 to 10 of 10
  1. #1
    Join Date
    Jul 2009
    Location
    Bayswater Nth Melbourne
    Posts
    3

    Unhappy Bubbles in Lacquer

    Hi Guys,
    Im a boilermaker that has decided to use some blackwood slabs given to me as table tops. I've been enjoying myself up to this point. I'm now applying, by brush, Feast Watson Weatherproof High Gloss. To my dismay, after I've put on a couple of coats, I have ended up with tiny bubbles in the finish.
    F.W. Fungishield was used to prime. I rinse my brush in turps then rinse in soapy water. I've sanded back, tried thin coats, tried thick coats.I'm at the point of taking to a pro but I dont want it to beat me!
    Any advice would be great.

    Regards,
    Col.

  2. #2
    Join Date
    Nov 2006
    Location
    t
    Posts
    79

    Default

    There is usually 2 reasons for bubbles.

    First one is the air coming out of the pores in the timber, but because it sounds like you have put a few coats on the most likely reason is mixing bubbles.
    When you stir the finish be very, very gentle, if you are too vigorous you can aerate it. If you let it stand for a few minutes before application the bubbles usually rise out.

    From Feast Watson site

    Stir gently before and during use with a flat blade stirrer, being careful not to introduce bubbles.
    .

  3. #3
    Join Date
    Jul 2009
    Location
    Bayswater Nth Melbourne
    Posts
    3

    Default

    I took note of stiring from the the can instructions. I'm going to be more careful with the brush today and see how I go. I'm going to thin it a little bit too, hopfully this may stop 'em appearing.

  4. #4
    Join Date
    Aug 2008
    Location
    Bendigo
    Age
    51
    Posts
    0

    Default

    Had similar probs recently when applying Cabotane to an MDF top. Didnt thin it at all. Used a roller.

    It was only for a shed table, so it wasnt the end of the world. Not sure if applying by roller would make the prob worse or not.
    www.lockwoodcanvas.com.au

    I will never be the person who has everything, not when someone keeps inventing so much cool new stuff to buy.

    From an early age my father taught me to wear welding gloves . "Its not to protect your hands son, its to put out the fire when u set yourself alight".

  5. #5
    Join Date
    May 1999
    Location
    Grovedale (Geelong) Victoria
    Age
    75
    Posts
    9,665

    Default

    Also caused by poor brushes. Most are made for paint and will often incorporate bubbles into the finish during application especially if the finish is slopped on the same way that paint is. They can often be removed by blowing on the finish through a straw as soon as they appear. Also heat applied to the wet finish will often bring them to the surface and help in eradicating them.

    But a really good brush and good application technique is the first and most effective solution.

    Cheers - Neil

  6. #6
    Join Date
    Jul 2008
    Location
    oakford w.a
    Posts
    0

    Default

    as neil said heat
    I run a soft flame over the wet finsh,to remove bubbles works every time.

  7. #7
    Join Date
    Jul 2009
    Location
    Bayswater Nth Melbourne
    Posts
    3

    Default

    Thanks for the advice fellas. I tried one more coat with it thinned a little before I got the advice. No luck, just smaller bubbles! I was talking to a spray-painter the day after and I weakend to his offer to spray them. But I will try some of the techniquics in the near future plus get a brush to suit. I didnt know, but suspected, my problems may have been related to my brush. How do I tell that it will be suitable for lacquer?
    Col.

  8. #8
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    2,966

    Default

    I enjoy painting. So when I go and buy a brush for painting the only thing that I care about is that this brush does not shed hair. This is also very true for applying finish on your wood working. At your local hardware store you will get a varierty to choose from. From the cheap to the expensive, it is hard to tell you which brush will be better. For me I perfer to have a tapered brush, and not too wide a brush, about 38 - 50mm for most wood jobs.

    Now when painting it does not matter too much how you apply as long as the final stroke is from top to bottom.

    When applying a finish on wood you have to be a little more caring on the amount of finish in the brush. Does not have to be fully loaded with finish to get a coat going.

    Apply the finish,,,, slowly and try to follow a patten or path.

  9. #9
    Join Date
    Aug 2004
    Location
    Sunbury, Victoria, Au.
    Posts
    0

    Default

    Quote Originally Posted by Christos View Post
    I enjoy painting....
    Russell (aka Mulgabill)
    "It is as it is"

  10. #10
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    2,966

    Default

    Quote Originally Posted by Mulgabill View Post


Similar Threads

  1. bubbles in plaster and more ?
    By potts1b in forum PLASTERING
    Replies: 2
    Last Post: 24th January 2007, 11:51 PM
  2. Air bubbles in paint
    By boxers in forum FINISHING
    Replies: 3
    Last Post: 9th June 2006, 07:57 AM
  3. Bubbles in Mirrortone
    By fredthegrub in forum FINISHING
    Replies: 2
    Last Post: 4th January 2002, 01:23 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •