Thanks: 0
Likes: 19
Needs Pictures: 0
Picture(s) thanks: 1
Results 1 to 15 of 23
-
17th December 2022, 11:03 AM #1Novice
- Join Date
- Jan 2014
- Location
- Australia
- Posts
- 15
Wood identification... ok for chopping boards?
Hi everyone, I have a coffee table that I’m not using anymore and I thought I’d cut it up to make some chopping boards. I am an absolute noob and not even sure if this is hardwood or not ( I think it is)
Can you please tell me what you think it might be and if it is suitable for chopping boards? SEE ATTACHED PIC
-
17th December 2022, 03:17 PM #2GOLD MEMBER
- Join Date
- May 2015
- Location
- Brisbane
- Posts
- 1,122
If you are cutting cooked or raw meat or veg you need a closed/tight grained timber, for bread and other dry foods an open grain will pass.
I believe meats should be cut on nylon boards that are easy to clean and do not harbour nasties. Ask butchers why they use them.
-
17th December 2022, 03:28 PM #3GOLD MEMBER
- Join Date
- Mar 2003
- Location
- Newcastle
- Age
- 69
- Posts
- 736
As far as I can see butchers are all still using end grain wooden chopping blocks. It seems that the wooden blocks are actually germicidal while nylon or other plastics can harbour the nasties deep in fine cut marks even through a hot wash.
-
17th December 2022, 05:08 PM #4
Back to the original question, my first guess from the pic would be Vic Ash/Tassie Oak. Remove the original finish and apply mineral oil should be OK.
Aside from all the blather about what wood is suitable for a cutting board, I'm yet to see any report of anybody actually being affected by cutting on standard Aussie hardwoods. What you might find if it is Vic Ash etc, it may stain blue if it gets wet.Franklin
-
17th December 2022, 07:46 PM #5
+1 Tassy Oak / Vic Ash , though you would need to see the end grain to be 100% sure.
-
18th December 2022, 08:46 AM #6GOLD MEMBER
- Join Date
- Dec 2010
- Location
- Mornington Peninsula
- Posts
- 2,464
Without seeing the end grain I would go for VIC Ash.
-
18th December 2022, 03:09 PM #7
I have a WA sheoak one as well as a Jarrah one (Cutting boards) have had them for years with no ill affects,touch wood.
I would clean the surface off back to raw timber as has been suggested.I leave mine bare finished.Johnno
Everyone has a photographic memory, some just don't have film.
-
21st April 2023, 01:45 PM #8Novice
- Join Date
- Jan 2014
- Location
- Australia
- Posts
- 15
Finally got around to pulling it apart, see attachment for pic of endgrain. 7-E47489-E-2-DF1-4-A87-A77-D-260-EFD7465-AD hosted at ImgBB — ImgBB
-
21st April 2023, 03:23 PM #9GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,585
I think the end grain confirms the initial ID of Vic Ash.
-
22nd April 2023, 12:29 AM #10
This is is a dangerous furphy created by a well known plastics manufacturer many years ago. The CSIRO did extensive testing over 20 years ago and found that wood was a far more hygienic material than plastic. Refer CSIRO website, or search this Forum - it's been discussed in the past.
Jason: your board looks like one of the "ash" type eucalypts - possibly mountain ash. It should be fine. For appearance, you can give it an oil finish. Over the years I have used boiled linseed, olive oil, palm oil, peanut oil, what ever we are using in the kitchen. All work provided you don't lay it on too thick.
-
22nd April 2023, 02:20 AM #11Senior Member
- Join Date
- Jul 2008
- Location
- geelong
- Posts
- 328
This - once finish is removed should be fine -avoid highly oily woods -cypress pine etc. more because of the taste than anything else.
-
22nd April 2023, 12:13 PM #12GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,585
Yeah, but wood hasn't changed in the last 20 years, whereas plastics have. I wonder what the results would be if they ran the study again today with newer plastics? And cleaning a wooden board properly is far more involved than throwing a plastic chopping board into a dishwasher. How long does wood's anti-bacterial property last? How many wash cycles? I can't help thinking this was one of those studies that doesn't translate well into the real world.
-
22nd April 2023, 12:17 PM #13GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,585
I used pure tung oil on my wooden breadboard. It looks fantastic, but you need patience. I applied about ten coats, at one coat per day, to get a nice sheen. After that, I'm told it only needs a couple of coats to rejuvenate the finish when it gets a bit dull.
-
22nd April 2023, 02:29 PM #14
I make end grain cutting boards / butcher blocks. My wife still has the first (and biggest) one I ever made on the kitchen bench and uses it every day. I would back a well made and properly sealed wood board against some lightweight piece of plastic any day of the week. My boards are all sealed (drowned) with a good quality foodsafe oil followed by multiple applications of bees wax. To clean them after use, simply wipe with a clean, warm (not hot) damp cloth - never put them in a dishwasher (mine wouldn't fit in one anyway) and don't use detergents on them. The finish on the one in our kitchen still looks exactly the same as the day it was first used.
IMG_2521.jpg IMG_2874.jpg
-
22nd April 2023, 04:36 PM #15
Similar Threads
-
Chopping boards
By macka75 in forum FINISHINGReplies: 20Last Post: 20th December 2006, 02:21 AM