Results 1 to 14 of 14
  1. #1
    Join Date
    May 2004
    Location
    Surrey Downs SA
    Age
    49
    Posts
    11

    Default storing silicone sealant

    Does anyone have any bright ideas on storing silicone sealant?

    I tend to seal small jobs like gutters and downpipes and recently used some sealant that i had stored, a near full tube with a nail in the nozzle and silicone smeared around the end, this seams to work on most sealants (short term) but not this particular roof and gutter silicone which cured in the tube to make a nice sized silicone sausage.

    It has also been suggested to use alfoil and glad wrap to cover end once nozzle removed, any other suggestions?
    I tell my wife, it's not a lie if i believe it's true

  2. #2
    Join Date
    May 2003
    Location
    Kuranda, paradise, North Qld
    Age
    63
    Posts
    2,026

    Default

    Wise,
    when you've finished using it keep the nozzle on and pump a little bit of fresh stuff out. Wipe this off with a tissue or rage and use masking tape to seal the nozzle end then pop the whole thing in the fridge. Works pretty well for me most of the time.

    Mick
    "If you need a machine today and don't buy it,

    tomorrow you will have paid for it and not have it."

    - Henry Ford 1938

  3. #3
    Join Date
    Nov 2003
    Location
    Australia and France
    Posts
    2,869

    Default

    Fridge.

    I once knew the reason, something to do with slowing the chemical reaction...once oxygen (or one of the other gases in the air) gets to it, a chain reaction happens - a bit like adding water to cement. That's why you squeeze the fresh stuff out and cap it IMMEDIATELY as well.

    Hope that adds to the wealth of useless info on the web!

    Cheers,

    P

  4. #4
    Join Date
    Oct 2002
    Location
    Brisbane, QLD, Australia
    Age
    47
    Posts
    0

    Default

    I found wrapping the threads of the tube where the nozzle connects with regular thread sealing tape helps stop air getting in that way. A nail in the top usually seals that, although often some part in the nozzle sets up, but is easily removed without too much loss.
    How much wood could the woodchuck chuck if the woodchuck could chuck wood?

  5. #5
    Join Date
    Feb 2003
    Location
    Garvoc VIC AUSTRALIA
    Posts
    3,208

    Default

    And always keep a spare new tube just in case.
    Regards, Bob Thomas

    www.wombatsawmill.com

  6. #6
    Join Date
    Jan 2004
    Location
    Australian (in exile) - UK
    Posts
    62

    Default

    You just need an air tight seal, I recently (through my work) toured a factory were they fill the cartridges. Bulk silicon is stored in airtight 44 gallon drums for lengthy periods.

    Unfortunately once used the tubes are not necessarily airtight even with a nail in the end or a cap. The push in plastic thing at the bottom often leaks and allows air in when you store it. maybe a Tupperware type container would do the trick.

    Cheers Dave

  7. #7
    Join Date
    Apr 2004
    Location
    Melbourne
    Age
    65
    Posts
    66

    Default Do nothing

    I tried a few sealing efforts but have resorted to simply leaving a little silicon out the end of the nozzel and that is it.

    Next time I use the stuff, I pull out the plug. I normally don't need any tools if the sticking out bit is long enough and the time of storage is not too long.

    If it has been a long while (+6 months), removing the plug of solid silicon may require removing the nozzel and pushing the plug out the wider, threaded end using a screw driver or stick.
    cheers
    David

    ------------------------------------------------
    A society grows great when old men plant trees whose shade they’ll never sit in. (Greek proverb)

  8. #8
    Join Date
    Mar 2004
    Location
    Ballarat, Vic, Australia
    Age
    58
    Posts
    7

    Default

    I seal the nozzle with insulation tape after use. However, the best advice is when buying a tube of silicone (or anything else in a tube) - is to collect 2-3 extra screw on nozzles from the hardware shop. They don't charge extra. If you find the silicon is cured in the nozzle, just unscrew it (chuck away) and put on a new one. I have found this method pretty foolproof.

    Steve

  9. #9
    Join Date
    May 2004
    Location
    Surrey Downs SA
    Age
    49
    Posts
    11

    Default

    Thanks for all your replies,

    tried most of those suggestions except the fridge, might give it a go, also had a friend suggest the freezer, don't know how well this would work after waiting for it to defrost.

    As for Mick's suggestion on cleaning off excess silicone, "Wipe this off with a tissue or rage" rage normally breaks thing's for me, but if it works for you great (been reading too many of those posts picking on spelling and grammar issues)
    I tell my wife, it's not a lie if i believe it's true

  10. #10
    Join Date
    May 2004
    Location
    Surrey Downs SA
    Age
    49
    Posts
    11

    Default

    Echnidna,

    very wise man indeed, this solid tube of silicone caught me in the middle of doing some down pipe work just before a rainstorm,(external plumbing should always be done at the beginning or during a rainstorm it adds interest) instead of finishing the job i had to rush to get some more, good fun.
    I tell my wife, it's not a lie if i believe it's true

  11. #11
    Join Date
    Apr 2002
    Location
    Brisbane
    Posts
    0

    Default

    I've always used a screw rather than a nail, big enough to bite into the sides of the end of the tube.

    But if you leave it more than a month your chances are prety slim for a good outcome.

    some products are more & less tolerant than others. Sicaflex is a bugger no matter how much you try to seal the end, onece shes open it will be off in a few days.
    I've had no more gaps stay ok for months.

    cheers

  12. #12
    Join Date
    May 2004
    Location
    Moo, G'day from CASINO NSW the real home of Beef.
    Age
    59
    Posts
    445

    Default heres another method that I use

    A method I still use is one that I picked in my wasted youth (drag bikes & tin tops) for ensuring the expensive gasket compounds didn't go off between engine rebuilds. When the tasks finished, undo the nozzle place a piece of clear plastic between it and the threaded section of cartridge, do up, then get a screw with an aggressive thread a bit larger than opening and screw into it(I use the cordless & 8 g wood thread for this) put the whole thing into old plastic bag & tie off.
    It really works as I just finished an old tube of liq nails that was opened 3 yrs ago, and used maybe 3-4 times over that period.

    Bruce C.

  13. #13
    Join Date
    May 2004
    Location
    Pakenham, outer Melb SE suburb, Vic
    Age
    55
    Posts
    549

    Default

    Gday all

    Couple of other ideas

    Drip candle wax over the tip, & also where the tip meets catridge

    Push a drinking straw down the tip, squeeze silicone into straw then store. Next time pull straw out & tip SHOULD be clear.

    Simplest way to keep airtight could be store under water somehow?

    Good idea as mentioned to keep spare tube(s) on hand. Another tip, if putting up Ceramalite (embossed tile-look panelling) buy PLENTY (3X recommended) quantity of Liquid Nails & later return the unused tubes, to save the midnight dash (& paying through the nose) to Safeway....DAMHIKT :eek:

    Cheers.........Sean

  14. #14
    Join Date
    Jul 2003
    Location
    Mt Druitt NSW
    Age
    65
    Posts
    139

    Default

    Quote Originally Posted by soundman
    I've always used a screw rather than a nail, big enough to bite into the sides of the end of the tube.
    I've found that a wooden golf tee works better than screws - no gap around the thread and larger than a nail.

    Whilst I play golf at company functions, I don't use the wooden tees - the plastic ones are much better - I wouldn't waste those on a tube of silicone.
    ______________
    Mark
    They only call it a rort if they're not in on it

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •