![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 7 of 7
Thread: New member from Perth
-
5th October 2013, 01:38 PM #1
New Member
- Join Date
- May 2013
- Location
- Perth
- Posts
- 1
New member from Perth
Hi everyone,
Customary introduction -tips hat-
Was given a bandsaw (BP-305) as a present at the start of this year from my fiancee, was so happy with her performance as a fiancee that I've promoted her to wife. (But that makes me liable to give her a Kitchenaid or a new set of pots&pans around the same price doesnt it)
Been a slow learning curve as I have been busy. But I am moving along well and have the projects in mind:
- DIY Drill Press from a hand drill
- Jewellery box
- Work bench
- Small greenhouse
Would love to know if there's a service where a person comes over and does a bandsaw tune up for me. I've done it according to the manufacturer's recommendations and also "Taunton's Mastering your bandsaw" video, but because I don't have exactly the same setup, I'm a little worried that the machine isn't set up well.
Cheers!
-
5th October 2013, 05:48 PM #2
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
Welcome aboard the nuthouse.
Was given a bandsaw (BP-305) as a present at the start of this year from my fiancee, was so happy with her performance as a fiancee that I've promoted her to wife. (But that makes me liable to give her a Kitchenaid or a new set of pots&pans around the same price doesnt it)
Been a slow learning curve as I have been busy. But I am moving along well and have the projects in mind:
- DIY Drill Press from a hand drill
- Jewellery box
- Work bench
- Small greenhouse
Would love to know if there's a service where a person comes over and does a bandsaw tune up for me. I've done it according to the manufacturer's recommendations and also "Taunton's Mastering your bandsaw" video, but because I don't have exactly the same setup, I'm a little worried that the machine isn't set up well.
Cheers!
-
5th October 2013, 06:02 PM #3
Gidday. welcome aboard and may your journey with us be a pleasant one. Check out the bandsaw section for some answers.
Regards Rumnut.
SimplyWoodwork
Qld. Australia.
-
6th October 2013, 07:02 AM #4
welcome aboard
-
12th October 2013, 11:52 AM #5
Welcome to the forum.
-
18th October 2013, 03:58 PM #6
G'Day & Welcome to a top forum.
There are quite a few members in and around Perth.
You'll find a heap of helpful & knowledgeable blokes & ladies on the forum and for most very willing to assist.
Make sure you show off your handiwork as everyone loves a photo, especially WIP photos with build notes.
Enjoy the forum.
Enjoy your woodwork.
Cheers crowie
-
21st October 2013, 10:31 PM #7
GOLD MEMBER
- Join Date
- May 2013
- Location
- Rockhampton QLD
- Age
- 69
- Posts
- 1,570
Welcome to the forum.
Similar Threads
-
New Member from perth
By JordsWoodShop in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 5Last Post: 15th November 2011, 07:57 AM -
GOING TO: Perth - Melb and Perth - Brisbane
By BobL in forum MEMBERS TRANSPORTReplies: 0Last Post: 31st August 2011, 10:22 AM