Results 1 to 6 of 6
  1. 27th July 2013, 02:21 PM #1
    startarot
    startarot is offline New Member
    Join Date
    Jul 2013
    Location
    Australia
    Posts
    1

    Default G'day New here- but im puzzled over a project

    Hey all - I am currently making a Manual Cylindrical screen printer
    the only problem is i can do is the frame etc, but the rollers
    i have the trouble of making them or where to start..

    Here is a example of the project i am stuck with..thanks in advance
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  2. 27th July 2013, 04:03 PM #2
    crowie's Avatar
    crowie
    crowie is offline Life's Good, Enjoy each new day & try to encourage
    Join Date
    Dec 2009
    Location
    Faulconbridge, Lower Blue Mountains
    Age
    68
    Posts
    2,576

    Default

    G'Day & Welcome to a top forum "startarot".
    There are a heap of members in and around the country plus the world.
    Sorry but can't help much on your question except to say ensure the shaft is lubricated & you have washers either side of the rollers.
    You'll find a heap of helpful & knowledgeable blokes & ladies on the forum and for most very willing to assist.
    Make sure you show off your handiwork as everyone loves a photo, especially WIP photos with build notes.
    Enjoy the forum.
    Enjoy your woodwork.
    Cheers crowie
    Reply With Quote Reply With Quote
  3. 28th July 2013, 09:39 AM #3
    tdrumnut's Avatar
    tdrumnut
    tdrumnut is offline Keeper of the wood
    Join Date
    Jan 2011
    Location
    Ormeau, Gold Coast, Australia
    Posts
    203

    Default

    Welcome aboard, may your journey be a pleasant one.
    Regards Rumnut.

    SimplyWoodwork
    Qld. Australia.
    Reply With Quote Reply With Quote
  4. 30th July 2013, 06:58 PM #4
    JJF's Avatar
    JJF
    JJF is offline GOLD MEMBER
    Join Date
    May 2011
    Location
    FRANCE
    Age
    59
    Posts
    1,889

    Default

    Welcome to a forum
    Reply With Quote Reply With Quote
  5. 30th July 2013, 11:34 PM #5
    Christos's Avatar
    Christos
    Christos is offline Mildly Moderate
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    2,966

    Default

    I am going to guess that you might want these rollers made out of wood so take a look at the Wood turning sub-section of the forum and post the question there.

    WOODTURNING - GENERAL

    And welcome to the forum.
    Reply With Quote Reply With Quote
  6. 31st July 2013, 03:25 PM #6
    bundy253
    bundy253 is offline New Member
    Join Date
    Jun 2013
    Location
    australia
    Posts
    2

    Default

    the wheels look like skate board wheels (I would buy a cheap skate board from kmart you get wheels bearings etc)
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. G'day Blokes - Bondwood/Fibreglass Boat Project
    By sullyman35 in forum G'day mate - THE WELCOME WAGON -Introduce yourself
    Replies: 3
    Last Post: 28th January 2009, 12:57 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules