![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 15 of 17
-
22nd March 2013, 09:32 AM #1
Replacement for bump feed on Ryobi whipper snippers
Had a couple of Ryobi whipper snippers over the years. Major problem that I've had with them is the bump feed mechanism. The cord snaps and then you have to re-assemble the line sometimes 2 or 3 times during the session that it's being used. What do others use? Heard of aftermarket gear, is it any better and where do you source it from?
-
22nd March 2013, 10:12 AM #2
SENIOR MEMBER
- Join Date
- Jul 2003
- Location
- Melbourne
- Age
- 53
- Posts
- 0
Does the bump feed actually work? does your cable just disapear in a tangle mess after about 2 minutes of use?
I know this is going to sound stupid but my ryobi bump feed never worked then one day (before I smashed it to pieces) I wound the cable in the opposite direction to the arrows on the spool and guess what, it worked perfectly for the first time ever...
I dont know why but it works perfectly in reverse
Probably wont work, but it might be worth a try.
joez
-
22nd March 2013, 10:15 AM #3
I do exactly as the instructions specify. Don't get so much a tangled mess as cord getting stuck and not feeding or one end breaking off and not feeding.
-
22nd March 2013, 10:33 AM #4
SENIOR MEMBER
- Join Date
- Jul 2003
- Location
- Melbourne
- Age
- 53
- Posts
- 0
-
22nd March 2013, 03:02 PM #5
GOLD MEMBER
- Join Date
- Oct 2003
- Location
- Sydney,Australia
- Posts
- 42
I've gone through a couple of weed whackers, the problem is not unique to Ryobi, it is generic.
I bought one of the fixed head line holders at a WWW show a few years back - the type where you just stick a length of line in the hole and there are metal grippers inside. The grippers are a waste of time after they get the first taste of mulched grass as they then become glued in place.
Don't give up yet. I found that you can just shove a length of line in and tie a quick knot in the end which stops it falling out. The only down side is that you have to stop the engine to put in new line (but you were already doing that when the 'auto feed' didn't), and carry a few spare lengths of cord in your back pocket.
-
22nd March 2013, 04:14 PM #6
I have a Stihl FS-85, and the bump feed head on that is a piece of crap too. It isn't just Ryobi.
We recently had a new Stihl dealer open up near us, and I must have mentioned the issue with the bump head while buying other parts from him.
"Oh, everyone knows they don't work properly" says he.......ahhhhhh
He sold me one of these as a replacement
Speed-Feed Fast Loading Trimmer Head, Speed Feed Trimmers | SpeedFeedHead.com
This is the US site showing how the product works, but I had no trouble buying one here locally.
Best thing since sliced bread. Easy to load, and feeds line reliably every time. It just works. I'm just kicking myself that I only discovered this by chance, and put up with the crappy Stihl bump head for all those years. I also use a metal Weedwakka blade for heavier stuff, but the SpeedFeed bump head does for 80% of my regular cutting along fencelines etc.
-
22nd March 2013, 04:35 PM #7
I had a Homelite originally that didn't last very long as the cord seemed to fuse together in the bump head. I managed to get some relief by using the next higher guage line than it was specified for. One mower shop suggested adding talc to the spool to help it along.
I upgraded the Homelite with a Kawaskai and never had a problem with the feed, although I started out using the heavier guage line, when that ran out I finished off the light weight line from the Homelite without issue.
This brush cutter has been going for 10 years now and the screw on the bottom of the head is now almost useless as it has been bumped so many times the head slots have disappeared. I'm hoping I will be able to extend it's life by just purchasing a replacement screw.
-
22nd March 2013, 05:31 PM #8
SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 36
I think Mr Brush you have the same one I have,have lost the packaging but by your desciption I think it is the one.
Works great,just wind in about 3 meters of line and go for it.
The last weed trimmer i bought the guy put one on included in the deal,he said that all his pro and shire customers swear by it,nothing to wear out.
Fits all machines.
-
22nd March 2013, 07:38 PM #9
So? So? You going to keep this a secret or do you wish to share where these can be got from? HMMM?
I would love to grow my own food, but I can not find bacon seeds
-
22nd March 2013, 08:22 PM #10
I have a 27 yr old McCulloch bump feed that has never missed a beat. The only ting I have had to do is change the spark plug (once only) and replace a perished fuel hose. Never fails to start after the third pull
The person who never made a mistake never made anything
Cheers
Ray
-
22nd March 2013, 08:33 PM #11
I got my SpeedFeed head from a local power tools shop (Irelands in Mittagong), but I suspect several would keep it.
Might be just as easy to get one off EBay though - I did a quick google search on "SpeedFeed head Australia" and it came up with this
SPEED FEED HEAD 4.5" 450 trimmer line brushcutter bump head fastest reload usa | eBay
That's definitely the one I have. The specs list the types of arbour shaft it can be fitted to, but they seem to fit most machines from what I have seen.
I run 2.4mm line on mine with no problems at all.
-
23rd March 2013, 09:21 AM #12
SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 36
more detail
Tonto,sorry can't get the brand for a few days as my tool is at our holiday house.
I got it at Mower Power in Dandenong,it is from the USA.
Mower Power are a chain maybe you have one near were you shop,good luck
They fit almost all machines the guy at MP told me.
-
28th March 2013, 10:08 AM #13
Thanks for those comments, looks like the Speed Feed is the way to go, just hope it's a good fit for the Ryobi.
-
28th March 2013, 10:18 AM #14
Only thing I can offer is to lay the cord out in the driveway on a warm day so it straightens a little (half hour).
If I wind new cord on directly from the new coil I get the cord breaking back into the roll as well.
But letting it warm and straighten seems to fix it for me (and its a ryobi as well).
-
28th March 2013, 02:45 PM #15
Good idea fly, won't hurt to try.
Similar Threads
-
Ryobi Whipper Snipper help
By petersemple in forum NOTHING AT ALL TO DO WITH RENOVATIONReplies: 14Last Post: 17th March 2010, 01:10 PM